Cisco Phone 8841
Kundenerfahrung gering - bei Interesse Kontakt mit Support aufnehmen
Anleitungen
Bedienungsanleitung:
Cisco Seite
Weitere auf der Webseite verfügbare Dokumente:
Webseite:
http://www.cisco.com/
Funktionen am Telefon
- Default Admin PIN: keine
- Ermittlung MAC Adresse und IP:
Auf Einstellung - Status - Product Information drücken - Neustart Prozedur:
noch unbekannt Reset Prozedur:
noch unbekannt
Webinterface
- Das Webinterface des Telefons wird mit folgendem Link erreicht:
http://<ip-adress-des-Telefons> - Kennwort nach Factory Reset:
admin - Neustart Prozedur:
Settings-> Rechts Reiter Starten -> Neustart -> OK - Eintrag des Provisionierungs-Servers
Advanced → Voice → Provisioning→ Profile Rule -> URL: Server eintragen, z. B. http://sip.teamsip.com/cisco/$MAU.cfg -> Submit all changess
Anleitung zur manuellen Konfiguration
noch keine Anleitung vorhanden.
Funktionsumfang
Das Telefon unterstützt folgende Leistungsmerkmale mit Firmware Version
Software Version: sip88xx.11-1-2MSR1-1.loads
Leistungsmerkmal | Verfügbar | Bemerkung |
---|---|---|
1. Provisionierung | ||
1.1 Power over Ethernet | ja | |
1.2 http Unterstützung | ja | |
1.3 https Unterstützung: | ja | |
1.4 Automatisches Konfigurationsupdate | ja | |
1.5 Firmware Update | ja | |
1.6 Automatische Zeiteinstellung | ja | |
1.7 Registration Timer | ja | |
1.8 DTMF RFC2833 | ja | |
1.9 Signalisierung UDP | ja | |
1.10 Signalisierung TCP | ja | |
1.11 Signalisierung TLS | ja | |
1.12 Verschlüsselung Sprachkanal mit SRTP | ja | |
1.13 Passwortschutz Weboberfläche | ja | |
2. Funktionstasten | ||
2.1 Lautstärke | ja | |
2.2 Stummschaltung | ja | |
2.3 Lauthören | ja | |
2.4 Bestätigen | ja | |
2.5 Abbrechen | ja | Die Auflegen Taste mit rotem Hörer |
2.6 Headset | ja | |
2.7 Nicht stören | ja | als programmierbare Taste unterhalb Display |
2.8 Wahlwiederholung | ja | |
2.9 Rufumleitung | ja | als programmierbare Taste unterhalb Display |
2.10 BLF Tasten Status | ja | |
2.11 BLF Tasten Übernahme | ja | |
2.12 BLF Tasten Kurzwahl | ja | |
2.13 Anruflisten | ja | |
3. Basisfunktionen | ||
3.1 Codec Unterstützung | ja | G.722, G.711(A/μ), G.723, G.729AB, G.726, GSM, iLBC |
3.2 Rufnummern Anzeige | ja | |
3.3 Rufnummern Anzeige nach Verbinden / Pickup | ja | |
3.4 Wahl bei aufgelegtem Hörer | ja | Nummer wählen, Call |
3.5 Anzeige Gesprächsdauer | ja | Display rechts neben gewählter Nummer |
3.6 Anklopfen | ja | |
3.7 Makeln | ja | Auswählen und RESUME |
3.8 Dreier-Konferenz | ja | |
3.9 Weiterleitung mit Rückfrage | ja | Anruf annehmen, "Halten", dann "Neues Gespräch aufbauen" drücken, Nummer wählen, sprechen und dann "Weiterleiten" drücken. |
3.10 Weiterleitung ohne Rückfrage | ja | Anruf annehmen. "BLIND TRANSFER" drücken und "CALL" drücken. |
3.11 Rückruf bei Besetzt | nicht getestet | |
3.12 Gespräch länger 30 Minuten | ja | |
4. Zusatzfunktionen | ||
4.1 verschiedene Klingeltöne | ja | |
4.2 Eigene Klingeltöne | nicht getestet | |
4.3 Vollduplex-Freisprechen | ja | |
4.5 Selbstbeschriftende Tasten | ja | |
4.6 XML-Anwendungen | nicht getestet | |
5. Telefonbuch | ||
5.1 Telefonbuch am Telefon | ja | |
5.2 Telefonbuch über LDAP | ja | Für LDAP konfigurierte "Telefonbuch" Taste unterhab Display links |
5.3 Telefonbuch über xml | ||
6. Anrufbeantworter | ||
6.1 MWI - Message Waiting Indicator | ja | Am Display als Symbol neben Leitung |
7. Headset | ||
7.1 Kabelheadsets | ja | |
7.2 EHS Headsets | ja | |
8. Erweiterungsmodule | ||
8.1 Funktionstasten Erweiterungsmodul | ja | Je nach Modell |
9. TeamSIP Funktionen | ||
9.1 Rufumleitung in TeamSIP | ja | |
9.2 Persönliches Telefonbuch aus TeamSIP | ja | Anzeige der Kontakte über LDAP |
9.3 Globales Telefonbuch aus Teamsip | ja | Anzeige der Kontakte über LDAP |
9.4 Callcenter Anmeldung mit Status Anzeige | ja | |
9.5 Neustart über SIP Notify | nicht getestet | |
9.6 Reload über SIP Notify | ja | |
9.7 Klingelton Unterscheidung intern/extern | nicht getestet |
TeamSIP Provisionierungs Template
Nutzbare Tasten
Unten aufgeführtes Beispiel nutzt 10 belegbare Tasten in der TeamSIP Weboberfläche.
Konfigurationsbeispiel
Parameter für dieses Template:
Name | Vorgabe |
---|---|
TF_FIRMWARE | sip88xx.11-1-2MSR1-1.loads |
Das geteste Telefon wurde mit dieser Provisionierungsvorlage als Telefon in TeamSIP konfiguriert:
TeamSIP Telefon Template
<?xml version="1.0" encoding="UTF-8" standalone="yes"?>
<device xsi:type="axl:XIPPhone" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance">
<flat-profile xmlns="http://www.sipura.net/xsd/SPA112" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.sipura.net/xsd/SPA112 http://www.sipura.net/xsd/SPA112/SPA112-1-2-1-004.xsd">
<!-- System Configuration -->
<Restricted_Access_Domains ua="na"></Restricted_Access_Domains>
<IVR_Admin_Passwd ua="na"></IVR_Admin_Passwd>
<Network_Startup_Delay ua="na">3</Network_Startup_Delay>
<!-- Miscellaneous Settings -->
<DNS_Query_TTL_Ignore ua="na">No</DNS_Query_TTL_Ignore>
<Syslog_Server ua="na"></Syslog_Server>
<Debug_Server ua="na"></Debug_Server>
<Debug_Level ua="na">3</Debug_Level> <!-- options: 0/1/2/3/3+Router/3+Coma -->
<!-- Configuration Profile -->
<Provision_Enable ua="na">Yes</Provision_Enable>
<Resync_On_Reset ua="na">Yes</Resync_On_Reset>
<Resync_Random_Delay ua="na">2</Resync_Random_Delay>
<Resync_At__HHmm_ ua="na"></Resync_At__HHmm_>
<Resync_At_Random_Delay ua="na">600</Resync_At_Random_Delay>
<Resync_Periodic ua="na">3600</Resync_Periodic>
<Resync_Error_Retry_Delay ua="na">3600</Resync_Error_Retry_Delay>
<Forced_Resync_Delay ua="na">14400</Forced_Resync_Delay>
<Resync_From_SIP ua="na">Yes</Resync_From_SIP>
<Resync_After_Upgrade_Attempt ua="na">Yes</Resync_After_Upgrade_Attempt>
<Resync_Trigger_1 ua="na"></Resync_Trigger_1>
<Resync_Trigger_2 ua="na"></Resync_Trigger_2>
<Resync_Fails_On_FNF ua="na">Yes</Resync_Fails_On_FNF>
<Profile_Rule ua="na">http://%TF_SIPSERVER%/cisco/$MAU.cfg</Profile_Rule>
<Profile_Rule_B ua="na"></Profile_Rule_B>
<Profile_Rule_C ua="na"></Profile_Rule_C>
<Profile_Rule_D ua="na"></Profile_Rule_D>
<Log_Resync_Request_Msg ua="na">$PN $MAC -- Requesting resync $SCHEME://$SERVIP:$PORT$PATH</Log_Resync_Request_Msg>
<Log_Resync_Success_Msg ua="na">$PN $MAC -- Successful resync $SCHEME://$SERVIP:$PORT$PATH</Log_Resync_Success_Msg>
<Log_Resync_Failure_Msg ua="na">$PN $MAC -- Resync failed: $ERR</Log_Resync_Failure_Msg>
<Report_Rule ua="na"></Report_Rule>
<SP_Default ua="na"></SP_Default>
<!-- Firmware Upgrade -->
<Upgrade_Enable ua="na">Yes</Upgrade_Enable>
<Upgrade_Error_Retry_Delay ua="na">3600</Upgrade_Error_Retry_Delay>
<!-- <Upgrade_Rule ua="na"/> -->
<Upgrade_Rule ua="na">http://%TF_SIPSERVER%/cisco/firmware/%TF_FIRMWARE%</Upgrade_Rule>
<Log_Upgrade_Request_Msg ua="na">$PN $MAC -- Requesting upgrade $SCHEME://$SERVIP:$PORT$PATH</Log_Upgrade_Request_Msg>
<Log_Upgrade_Success_Msg ua="na">$PN $MAC -- Successful upgrade $SCHEME://$SERVIP:$PORT$PATH -- $ERR</Log_Upgrade_Success_Msg>
<Log_Upgrade_Failure_Msg ua="na">$PN $MAC -- Upgrade failed: $ERR</Log_Upgrade_Failure_Msg>
<License_Keys ua="na"></License_Keys>
<Recovery_URL ua="na"></Recovery_URL>
<!-- Language -->
<Dictionary_Server_Script ua="na"/>
<Language_Selection ua="na">German</Language_Selection>
<Locale ua="na">de-DE</Locale>
<!-- CA Settings -->
<Custom_CA_URL ua="na"></Custom_CA_URL>
<!-- General Purpose Parameters -->
<GPP_A ua="na"></GPP_A>
<GPP_B ua="na"></GPP_B>
<GPP_C ua="na"></GPP_C>
<GPP_D ua="na"></GPP_D>
<GPP_E ua="na"></GPP_E>
<GPP_F ua="na"></GPP_F>
<GPP_G ua="na"></GPP_G>
<GPP_H ua="na"></GPP_H>
<GPP_I ua="na"></GPP_I>
<GPP_J ua="na"></GPP_J>
<GPP_K ua="na"></GPP_K>
<GPP_L ua="na"></GPP_L>
<GPP_M ua="na"></GPP_M>
<GPP_N ua="na"></GPP_N>
<GPP_O ua="na"></GPP_O>
<GPP_P ua="na"></GPP_P>
<GPP_SA ua="na"></GPP_SA>
<GPP_SB ua="na"></GPP_SB>
<GPP_SC ua="na"></GPP_SC>
<GPP_SD ua="na"></GPP_SD>
<!-- SIP Parameters -->
<Max_Forward ua="na">70</Max_Forward>
<Max_Redirection ua="na">5</Max_Redirection>
<Max_Auth ua="na">2</Max_Auth>
<SIP_User_Agent_Name ua="na">$VERSION</SIP_User_Agent_Name>
<SIP_Server_Name ua="na">$VERSION</SIP_Server_Name>
<SIP_Reg_User_Agent_Name ua="na"></SIP_Reg_User_Agent_Name>
<SIP_Accept_Language ua="na"></SIP_Accept_Language>
<DTMF_Relay_MIME_Type ua="na">application/dtmf-relay</DTMF_Relay_MIME_Type>
<Hook_Flash_MIME_Type ua="na">application/hook-flash</Hook_Flash_MIME_Type>
<Remove_Last_Reg ua="na">No</Remove_Last_Reg>
<Use_Compact_Header ua="na">No</Use_Compact_Header>
<Escape_Display_Name ua="na">No</Escape_Display_Name>
<RFC_2543_Call_Hold ua="na">Yes</RFC_2543_Call_Hold>
<Mark_All_AVT_Packets ua="na">Yes</Mark_All_AVT_Packets>
<SIP_TCP_Port_Min ua="na">5060</SIP_TCP_Port_Min>
<SIP_TCP_Port_Max ua="na">5080</SIP_TCP_Port_Max>
<CTI_Enable ua="na">No</CTI_Enable>
<!-- SIP Timer Values (sec) -->
<SIP_T1 ua="na">.5</SIP_T1>
<SIP_T2 ua="na">4</SIP_T2>
<SIP_T4 ua="na">5</SIP_T4>
<SIP_Timer_B ua="na">32</SIP_Timer_B>
<SIP_Timer_F ua="na">16</SIP_Timer_F>
<SIP_Timer_H ua="na">32</SIP_Timer_H>
<SIP_Timer_D ua="na">32</SIP_Timer_D>
<SIP_Timer_J ua="na">32</SIP_Timer_J>
<INVITE_Expires ua="na">240</INVITE_Expires>
<ReINVITE_Expires ua="na">30</ReINVITE_Expires>
<Reg_Min_Expires ua="na">1</Reg_Min_Expires>
<Reg_Max_Expires ua="na">7200</Reg_Max_Expires>
<Reg_Retry_Intvl ua="na">30</Reg_Retry_Intvl>
<Reg_Retry_Long_Intvl ua="na">1200</Reg_Retry_Long_Intvl>
<Reg_Retry_Random_Delay ua="na">0</Reg_Retry_Random_Delay>
<Reg_Retry_Long_Random_Delay ua="na">0</Reg_Retry_Long_Random_Delay>
<Reg_Retry_Intvl_Cap ua="na">0</Reg_Retry_Intvl_Cap>
<!-- Response Status Code Handling -->
<SIT1_RSC ua="na"></SIT1_RSC>
<SIT2_RSC ua="na"></SIT2_RSC>
<SIT3_RSC ua="na"></SIT3_RSC>
<SIT4_RSC ua="na"></SIT4_RSC>
<Try_Backup_RSC ua="na"></Try_Backup_RSC>
<Retry_Reg_RSC ua="na"></Retry_Reg_RSC>
<!-- RTP Parameters -->
<RTP_Port_Min ua="na">16384</RTP_Port_Min>
<RTP_Port_Max ua="na">16482</RTP_Port_Max>
<RTP_Packet_Size ua="na">0.020</RTP_Packet_Size>
<Max_RTP_ICMP_Err ua="na">0</Max_RTP_ICMP_Err>
<RTCP_Tx_Interval ua="na">0</RTCP_Tx_Interval>
<No_UDP_Checksum ua="na">No</No_UDP_Checksum>
<Stats_In_BYE ua="na">Yes</Stats_In_BYE>
<!-- SDP Payload Types -->
<NSE_Dynamic_Payload ua="na">100</NSE_Dynamic_Payload>
<AVT_Dynamic_Payload ua="na">101</AVT_Dynamic_Payload>
<INFOREQ_Dynamic_Payload ua="na"></INFOREQ_Dynamic_Payload>
<G726r32_Dynamic_Payload ua="na">2</G726r32_Dynamic_Payload>
<EncapRTP_Dynamic_Payload ua="na">112</EncapRTP_Dynamic_Payload>
<RTP-Start-Loopback_Dynamic_Payload ua="na">113</RTP-Start-Loopback_Dynamic_Payload>
<RTP-Start-Loopback_Codec ua="na">G711a</RTP-Start-Loopback_Codec> <!-- options: G711u/G711a/G726-32/G729a -->
<NSE_Codec_Name ua="na">NSE</NSE_Codec_Name>
<AVT_Codec_Name ua="na">telephone-event</AVT_Codec_Name>
<G711u_Codec_Name ua="na">PCMU</G711u_Codec_Name>
<G711a_Codec_Name ua="na">PCMA</G711a_Codec_Name>
<G726r32_Codec_Name ua="na">G726-32</G726r32_Codec_Name>
<G729a_Codec_Name ua="na">G729a</G729a_Codec_Name>
<EncapRTP_Codec_Name ua="na">encaprtp</EncapRTP_Codec_Name>
<!-- NAT Support Parameters -->
<Handle_VIA_received ua="na">No</Handle_VIA_received>
<Handle_VIA_rport ua="na">No</Handle_VIA_rport>
<Insert_VIA_received ua="na">No</Insert_VIA_received>
<Insert_VIA_rport ua="na">No</Insert_VIA_rport>
<Substitute_VIA_Addr ua="na">No</Substitute_VIA_Addr>
<Send_Resp_To_Src_Port ua="na">No</Send_Resp_To_Src_Port>
<STUN_Enable ua="na">Yes</STUN_Enable>
<STUN_Test_Enable ua="na">No</STUN_Test_Enable>
<STUN_Server ua="na">stun.teamfon.com</STUN_Server>
<EXT_IP ua="na"></EXT_IP>
<EXT_RTP_Port_Min ua="na"></EXT_RTP_Port_Min>
<NAT_Keep_Alive_Intvl ua="na">15</NAT_Keep_Alive_Intvl>
<Redirect_Keep_Alive ua="na">No</Redirect_Keep_Alive>
<!-- Linksys Key System Parameters -->
<Linksys_Key_System ua="na">No</Linksys_Key_System>
<Multicast_Address ua="na">224.168.168.168:6061</Multicast_Address>
<Key_System_Auto_Discovery ua="na">Yes</Key_System_Auto_Discovery>
<Key_System_IP_Address ua="na"></Key_System_IP_Address>
<Force_LAN_Codec ua="na">none</Force_LAN_Codec> <!-- options: none/G711u/G711a -->
<Station_Name ua="na"></Station_Name>
<!-- General -->
<Line_Enable_1_ ua="na">Yes</Line_Enable_1_>
<!-- Streaming Audio Server (SAS) -->
<SAS_Enable_1_ ua="na">No</SAS_Enable_1_>
<SAS_DLG_Refresh_Intvl_1_ ua="na">30</SAS_DLG_Refresh_Intvl_1_>
<SAS_Inbound_RTP_Sink_1_ ua="na"></SAS_Inbound_RTP_Sink_1_>
<!-- NAT Settings -->
<NAT_Mapping_Enable_1_ ua="na">No</NAT_Mapping_Enable_1_>
<NAT_Keep_Alive_Enable_1_ ua="na">No</NAT_Keep_Alive_Enable_1_>
<NAT_Keep_Alive_Msg_1_ ua="na">$NOTIFY</NAT_Keep_Alive_Msg_1_>
<NAT_Keep_Alive_Dest_1_ ua="na">$PROXY</NAT_Keep_Alive_Dest_1_>
<!-- Network Settings -->
<SIP_ToS_DiffServ_Value_1_ ua="na">0x68</SIP_ToS_DiffServ_Value_1_>
<SIP_CoS_Value_1_ ua="na">3</SIP_CoS_Value_1_>
<RTP_ToS_DiffServ_Value_1_ ua="na">0xb8</RTP_ToS_DiffServ_Value_1_>
<RTP_CoS_Value_1_ ua="na">6</RTP_CoS_Value_1_>
<Network_Jitter_Level_1_ ua="na">high</Network_Jitter_Level_1_> <!-- options: low/medium/high/very high/extremely high -->
<Jitter_Buffer_Adjustment_1_ ua="na">Yes</Jitter_Buffer_Adjustment_1_>
<!-- SIP Settings -->
<SIP_Transport_1_ ua="na">UDP</SIP_Transport_1_> <!-- options: UDP/TCP/TLS -->
<SIP_Port_1_ ua="na">5060</SIP_Port_1_>
<SIP_100REL_Enable_1_ ua="na">No</SIP_100REL_Enable_1_>
<EXT_SIP_Port_1_ ua="na"></EXT_SIP_Port_1_>
<Auth_Resync-Reboot_1_ ua="na">Yes</Auth_Resync-Reboot_1_>
<SIP_Proxy-Require_1_ ua="na"></SIP_Proxy-Require_1_>
<SIP_Remote-Party-ID_1_ ua="na">Yes</SIP_Remote-Party-ID_1_>
<SIP_GUID_1_ ua="na">No</SIP_GUID_1_>
<SIP_Debug_Option_1_ ua="na">none</SIP_Debug_Option_1_> <!-- options: none/1-line/1-line excl. OPT/1-line excl. NTFY/1-line excl. REG/1-line excl. OPT|NTFY|REG/full/full excl. OPT/full excl. NTFY/full excl. REG/full excl. OPT|NTFY|REG -->
<RTP_Log_Intvl_1_ ua="na">0</RTP_Log_Intvl_1_>
<Restrict_Source_IP_1_ ua="na">No</Restrict_Source_IP_1_>
<Referor_Bye_Delay_1_ ua="na">4</Referor_Bye_Delay_1_>
<Refer_Target_Bye_Delay_1_ ua="na">0</Refer_Target_Bye_Delay_1_>
<Referee_Bye_Delay_1_ ua="na">0</Referee_Bye_Delay_1_>
<Refer-To_Target_Contact_1_ ua="na">No</Refer-To_Target_Contact_1_>
<Sticky_183_1_ ua="na">No</Sticky_183_1_>
<Auth_INVITE_1_ ua="na">No</Auth_INVITE_1_>
<Reply_182_On_Call_Waiting_1_ ua="na">No</Reply_182_On_Call_Waiting_1_>
<Use_Anonymous_With_RPID_1_ ua="na">Yes</Use_Anonymous_With_RPID_1_>
<Use_Local_Addr_In_FROM_1_ ua="na">No</Use_Local_Addr_In_FROM_1_>
<!-- Call Feature Settings -->
<Blind_Attn-Xfer_Enable_1_ ua="na">No</Blind_Attn-Xfer_Enable_1_>
<MOH_Server_1_ ua="na"></MOH_Server_1_>
<Xfer_When_Hangup_Conf_1_ ua="na">Yes</Xfer_When_Hangup_Conf_1_>
<Conference_Bridge_URL_1_ ua="na"></Conference_Bridge_URL_1_>
<Conference_Bridge_Ports_1_ ua="na">3</Conference_Bridge_Ports_1_> <!-- options: 3/4/5/6/7/8/9/10 -->
<Enable_IP_Dialing_1_ ua="na">No</Enable_IP_Dialing_1_>
<Emergency_Number_1_ ua="na"></Emergency_Number_1_>
<Mailbox_ID_1_ ua="na"></Mailbox_ID_1_>
<!-- Proxy and Registration -->
<Proxy_1_ ua="na">%TF_SIPSERVER%</Proxy_1_>
<Outbound_Proxy_1_ ua="na">%TF_SIPSERVER%</Outbound_Proxy_1_>
<Use_Outbound_Proxy_1_ ua="na">No</Use_Outbound_Proxy_1_>
<Use_OB_Proxy_In_Dialog_1_ ua="na">Yes</Use_OB_Proxy_In_Dialog_1_>
<Register_1_ ua="na">Yes</Register_1_>
<Make_Call_Without_Reg_1_ ua="na">No</Make_Call_Without_Reg_1_>
<Register_Expires_1_ ua="na">3600</Register_Expires_1_>
<Ans_Call_Without_Reg_1_ ua="na">No</Ans_Call_Without_Reg_1_>
<Use_DNS_SRV_1_ ua="na">No</Use_DNS_SRV_1_>
<DNS_SRV_Auto_Prefix_1_ ua="na">No</DNS_SRV_Auto_Prefix_1_>
<Proxy_Fallback_Intvl_1_ ua="na">3600</Proxy_Fallback_Intvl_1_>
<Proxy_Redundancy_Method_1_ ua="na">Normal</Proxy_Redundancy_Method_1_> <!-- options: Normal/Based on SRV Port -->
<Mailbox_Subscribe_URL_1_ ua="na"></Mailbox_Subscribe_URL_1_>
<Mailbox_Subscribe_Expires_1_ ua="na">2147483647</Mailbox_Subscribe_Expires_1_>
<!-- Subscriber Information -->
<Display_Name_1_ ua="na">%TF_ACCOUNT%</Display_Name_1_>
<User_ID_1_ ua="na">%TF_ACCOUNT%</User_ID_1_>
<Password_1_ ua="na">%TF_PASSWORD%</Password_1_>
<Use_Auth_ID_1_ ua="na">No</Use_Auth_ID_1_>
<Auth_ID_1_ ua="na">%TF_ACCOUNT%</Auth_ID_1_>
<Resident_Online_Number_1_ ua="na"></Resident_Online_Number_1_>
<SIP_URI_1_ ua="na"></SIP_URI_1_>
<!-- Line Key 2 -->
<Extension_2_ ua="na">Disabled</Extension_2_>
<Short_Name_2_ ua="na">%TF_NTNAME_1%61</Short_Name_2_>
<Share_Call_Appearance_2_ ua="na">private</Share_Call_Appearance_2_>
<Extended_Function_2_ ua="na">fnc=blf+sd+cp;sub=%TF_NTNUMMER_1%@$PROXY;ext=%TF_NTNUMMER_1%@$PROXY</Extended_Function_2_>
<!-- Line Key 2 -->
<Extension_2_ ua="na">Disabled</Extension_2_>
<Short_Name_2_ ua="na">%TF_NTNAME_1%</Short_Name_2_>
<Share_Call_Appearance_2_ ua="na">private</Share_Call_Appearance_2_>
<Extended_Function_2_ ua="na">fnc=blf+sd+cp;sub=%TF_NTNUMMER_1%@$PROXY;ext=%TF_NTNUMMER_1%@$PROXY</Extended_Function_2_>
<!-- Line Key 3 -->
<Extension_3_ ua="na">Disabled</Extension_3_>
<Short_Name_3_ ua="na">%TF_NTNAME_2%</Short_Name_3_>
<Share_Call_Appearance_3_ ua="na">private</Share_Call_Appearance_3_>
<Extended_Function_3_ ua="na">fnc=blf+sd+cp;sub=%TF_NTNUMMER_2%@$PROXY;ext=%TF_NTNUMMER_2%@$PROXY</Extended_Function_3_>
<!-- Line Key 4 -->
<Extension_4_ ua="na">Disabled</Extension_4_>
<Short_Name_4_ ua="na">%TF_NTNAME_3%</Short_Name_4_>
<Share_Call_Appearance_4_ ua="na">private</Share_Call_Appearance_4_>
<Extended_Function_4_ ua="na">fnc=blf+sd+cp;sub=%TF_NTNUMMER_3%@$PROXY;ext=%TF_NTNUMMER_3%@$PROXY</Extended_Function_4_>
<!-- Line Key 5 -->
<Extension_5_ ua="na">Disabled</Extension_5_>
<Short_Name_5_ ua="na">%TF_NTNAME_4%</Short_Name_5_>
<Share_Call_Appearance_5_ ua="na">private</Share_Call_Appearance_5_>
<Extended_Function_5_ ua="na">fnc=blf+sd+cp;sub=%TF_NTNUMMER_4%@$PROXY;ext=%TF_NTNUMMER_4%@$PROXY</Extended_Function_5_>
<!-- Line Key 6 -->
<Extension_6_ ua="na">Disabled</Extension_6_>
<Short_Name_6_ ua="na">%TF_NTNAME_5%</Short_Name_6_>
<Share_Call_Appearance_6_ ua="na">private</Share_Call_Appearance_6_>
<Extended_Function_6_ ua="na">fnc=blf+sd+cp;sub=%TF_NTNUMMER_5%@$PROXY;ext=%TF_NTNUMMER_5%@$PROXY</Extended_Function_6_>
<!-- Line Key 7 -->
<Extension_7_ ua="na">Disabled</Extension_7_>
<Short_Name_7_ ua="na">%TF_NTNAME_6%</Short_Name_7_>
<Share_Call_Appearance_7_ ua="na">private</Share_Call_Appearance_7_>
<Extended_Function_7_ ua="na">fnc=blf+sd+cp;sub=%TF_NTNUMMER_6%@$PROXY;ext=%TF_NTNUMMER_6%@$PROXY</Extended_Function_7_>
<!-- Line Key 8 -->
<Extension_8_ ua="na">Disabled</Extension_8_>
<Short_Name_8_ ua="na">%TF_NTNAME_7%</Short_Name_8_>
<Share_Call_Appearance_8_ ua="na">private</Share_Call_Appearance_8_>
<Extended_Function_8_ ua="na">fnc=blf+sd+cp;sub=%TF_NTNUMMER_7%@$PROXY;ext=%TF_NTNUMMER_7%@$PROXY</Extended_Function_8_>
<!-- Line Key 9 -->
<Extension_9_ ua="na">Disabled</Extension_9_>
<Short_Name_9_ ua="na">%TF_NTNAME_8%</Short_Name_9_>
<Share_Call_Appearance_9_ ua="na">private</Share_Call_Appearance_9_>
<Extended_Function_9_ ua="na">fnc=blf+sd+cp;sub=%TF_NTNUMMER_8%@$PROXY;ext=%TF_NTNUMMER_8%@$PROXY</Extended_Function_9_>
<!-- Line Key 10 -->
<Extension_10_ ua="na">Disabled</Extension_10_>
<Short_Name_10_ ua="na">%TF_NTNAME_9%</Short_Name_10_>
<Share_Call_Appearance_10_ ua="na">private</Share_Call_Appearance_10_>
<Extended_Function_10_ ua="na">fnc=blf+sd+cp;sub=%TF_NTNUMMER_9%@$PROXY;ext=%TF_NTNUMMER_9%@$PROXY</Extended_Function_10_>
<!-- LDAP -->
<LDAP_Dir_Enable ua="na">Yes</LDAP_Dir_Enable>
<LDAP_Corp_Dir_Name ua="na">LDAP</LDAP_Corp_Dir_Name>
<LDAP_Server ua="na">%TF_SIPSERVER%</LDAP_Server>
<LDAP_Search_Base ua="na">ou=Teamfon,ou=userdata,ou=appls,dc=teamware,dc=de</LDAP_Search_Base>
<LDAP_Client_DN ua="na">uid=%TF_ACCOUNT%,ou=authentication,dc=teamfom,dc=de</LDAP_Client_DN>
<LDAP_Username ua="na">uid=%TF_ACCOUNT%,ou=authentication,dc=teamfom,dc=de</LDAP_Username>
<LDAP_Password ua="na">%TF_PASSWORD%</LDAP_Password>
<LDAP_Auth_Method ua="na">Simple</LDAP_Auth_Method>
<LDAP_Last_Name_Filter ua="na">sn:(sn=$VALUE*)</LDAP_Last_Name_Filter>
<LDAP_First_Name_Filter ua="na">givenName:(givenName=$VALUE*)</LDAP_First_Name_Filter>
<LDAP_Search_Item_3 ua="na">telephoneNumber</LDAP_Search_Item_3>
<LDAP_Item_3_Filter ua="na">telephoneNumber:(telephoneNumber=$VALUE*)</LDAP_Item_3_Filter>
<LDAP_Search_Item_4 ua="na">postalCode</LDAP_Search_Item_4>
<LDAP_Item_4_Filter ua="na">postalCode:(postalCode=$VALUE*)</LDAP_Item_4_Filter>
<LDAP_Display_Attrs ua="na">a=cn,n=cn;a=givenName,n=Vorname;a=sn,n=Nachname;a=telephoneNumber,n=Telefon;a=uid,n=uid;a=telNrBusiness1,n=Firma1;a=telNrBusiness2,n=Firma2;a=telNrMobile,n=Mobil</LDAP_Display_Attrs>
<LDAP_Number_Mapping ua="na">(<1408853:>xx.|<+1408853:>xx.|<+86212405:>xx.|<86212405:>xx.)</LDAP_Number_Mapping>
<!-- Supplementary Service Subscription -->
<Call_Pickup_Code ua="na">**</Call_Pickup_Code>
<Call_Waiting_Serv_1_ ua="na">Yes</Call_Waiting_Serv_1_>
<Block_CID_Serv_1_ ua="na">Yes</Block_CID_Serv_1_>
<Block_ANC_Serv_1_ ua="na">Yes</Block_ANC_Serv_1_>
<Dist_Ring_Serv_1_ ua="na">Yes</Dist_Ring_Serv_1_>
<Cfwd_All_Serv_1_ ua="na">Yes</Cfwd_All_Serv_1_>
<Cfwd_Busy_Serv_1_ ua="na">Yes</Cfwd_Busy_Serv_1_>
<Cfwd_No_Ans_Serv_1_ ua="na">Yes</Cfwd_No_Ans_Serv_1_>
<Cfwd_Sel_Serv_1_ ua="na">Yes</Cfwd_Sel_Serv_1_>
<Cfwd_Last_Serv_1_ ua="na">Yes</Cfwd_Last_Serv_1_>
<Block_Last_Serv_1_ ua="na">Yes</Block_Last_Serv_1_>
<Accept_Last_Serv_1_ ua="na">Yes</Accept_Last_Serv_1_>
<DND_Serv_1_ ua="na">Yes</DND_Serv_1_>
<CID_Serv_1_ ua="na">Yes</CID_Serv_1_>
<CWCID_Serv_1_ ua="na">Yes</CWCID_Serv_1_>
<Call_Return_Serv_1_ ua="na">Yes</Call_Return_Serv_1_>
<Call_Redial_Serv_1_ ua="na">Yes</Call_Redial_Serv_1_>
<Call_Back_Serv_1_ ua="na">Yes</Call_Back_Serv_1_>
<Three_Way_Call_Serv_1_ ua="na">Yes</Three_Way_Call_Serv_1_>
<Three_Way_Conf_Serv_1_ ua="na">Yes</Three_Way_Conf_Serv_1_>
<Attn_Transfer_Serv_1_ ua="na">Yes</Attn_Transfer_Serv_1_>
<Unattn_Transfer_Serv_1_ ua="na">Yes</Unattn_Transfer_Serv_1_>
<MWI_Serv_1_ ua="na">Yes</MWI_Serv_1_>
<VMWI_Serv_1_ ua="na">Yes</VMWI_Serv_1_>
<Speed_Dial_Serv_1_ ua="na">Yes</Speed_Dial_Serv_1_>
<Secure_Call_Serv_1_ ua="na">Yes</Secure_Call_Serv_1_>
<Referral_Serv_1_ ua="na">Yes</Referral_Serv_1_>
<Feature_Dial_Serv_1_ ua="na">Yes</Feature_Dial_Serv_1_>
<Service_Announcement_Serv_1_ ua="na">No</Service_Announcement_Serv_1_>
<Reuse_CID_Number_As_Name_1_ ua="na">Yes</Reuse_CID_Number_As_Name_1_>
<!-- Audio Configuration -->
<Preferred_Codec_1_ ua="na">G711a</Preferred_Codec_1_> <!-- options: G711u/G711a/G726-32/G729a -->
<Second_Preferred_Codec_1_ ua="na">G711u</Second_Preferred_Codec_1_> <!-- options: Unspecified/G711u/G711a/G726-32/G729a -->
<Third_Preferred_Codec_1_ ua="na">Unspecified</Third_Preferred_Codec_1_> <!-- options: Unspecified/G711u/G711a/G726-32/G729a -->
<Use_Pref_Codec_Only_1_ ua="na">No</Use_Pref_Codec_Only_1_>
<Use_Remote_Pref_Codec_1_ ua="na">No</Use_Remote_Pref_Codec_1_>
<Codec_Negotiation_1_ ua="na">Default</Codec_Negotiation_1_> <!-- options: Default/List All -->
<G729a_Enable_1_ ua="na">Yes</G729a_Enable_1_>
<Silence_Supp_Enable_1_ ua="na">No</Silence_Supp_Enable_1_>
<G726-32_Enable_1_ ua="na">Yes</G726-32_Enable_1_>
<Silence_Threshold_1_ ua="na">medium</Silence_Threshold_1_> <!-- options: high/medium/low -->
<FAX_V21_Detect_Enable_1_ ua="na">Yes</FAX_V21_Detect_Enable_1_>
<Echo_Canc_Enable_1_ ua="na">Yes</Echo_Canc_Enable_1_>
<FAX_CNG_Detect_Enable_1_ ua="na">Yes</FAX_CNG_Detect_Enable_1_>
<FAX_Passthru_Codec_1_ ua="na">G711a</FAX_Passthru_Codec_1_> <!-- options: G711u/G711a -->
<FAX_Codec_Symmetric_1_ ua="na">Yes</FAX_Codec_Symmetric_1_>
<DTMF_Process_INFO_1_ ua="na">Yes</DTMF_Process_INFO_1_>
<FAX_Passthru_Method_1_ ua="na">NSE</FAX_Passthru_Method_1_> <!-- options: None/NSE/ReINVITE -->
<DTMF_Process_AVT_1_ ua="na">Yes</DTMF_Process_AVT_1_>
<FAX_Process_NSE_1_ ua="na">Yes</FAX_Process_NSE_1_>
<DTMF_Tx_Method_1_ ua="na">Auto</DTMF_Tx_Method_1_> <!-- options: InBand/AVT/INFO/Auto/InBand+INFO/AVT+INFO -->
<FAX_Disable_ECAN_1_ ua="na">No</FAX_Disable_ECAN_1_>
<DTMF_Tx_Mode_1_ ua="na">Strict</DTMF_Tx_Mode_1_> <!-- options: Normal/Strict -->
<DTMF_Tx_Strict_Hold_Off_Time_1_ ua="na">70</DTMF_Tx_Strict_Hold_Off_Time_1_>
<FAX_Enable_T38_1_ ua="na">Yes</FAX_Enable_T38_1_>
<Hook_Flash_Tx_Method_1_ ua="na">None</Hook_Flash_Tx_Method_1_> <!-- options: None/AVT/INFO -->
<FAX_T38_Redundancy_1_ ua="na">1</FAX_T38_Redundancy_1_> <!-- options: 0/1/2/3 -->
<FAX_T38_ECM_Enable_1_ ua="na">Yes</FAX_T38_ECM_Enable_1_>
<FAX_Tone_Detect_Mode_1_ ua="na">caller or callee</FAX_Tone_Detect_Mode_1_> <!-- options: caller or callee/caller only/callee only -->
<Symmetric_RTP_1_ ua="na">No</Symmetric_RTP_1_>
<FAX_T38_Return_to_Voice_1_ ua="na">No</FAX_T38_Return_to_Voice_1_>
<!-- Dial Plan -->
<Dial_Plan_1_ ua="na">(*xx|[3469]11|0|00|[2-9]xxxxxx|1xxx[2-9]xxxxxxS0|xxxxxxxxxxxx.)</Dial_Plan_1_>
<!-- FXS Port Polarity Configuration -->
<Idle_Polarity_1_ ua="na">Forward</Idle_Polarity_1_> <!-- options: Forward/Reverse -->
<Caller_Conn_Polarity_1_ ua="na">Forward</Caller_Conn_Polarity_1_> <!-- options: Forward/Reverse -->
<Callee_Conn_Polarity_1_ ua="na">Forward</Callee_Conn_Polarity_1_> <!-- options: Forward/Reverse -->
<!-- General -->
<Line_Enable_2_ ua="na">Yes</Line_Enable_2_>
<!-- Streaming Audio Server (SAS) -->
<SAS_Enable_2_ ua="na">No</SAS_Enable_2_>
<SAS_DLG_Refresh_Intvl_2_ ua="na">30</SAS_DLG_Refresh_Intvl_2_>
<SAS_Inbound_RTP_Sink_2_ ua="na"></SAS_Inbound_RTP_Sink_2_>
<!-- NAT Settings -->
<NAT_Mapping_Enable_2_ ua="na">No</NAT_Mapping_Enable_2_>
<NAT_Keep_Alive_Enable_2_ ua="na">No</NAT_Keep_Alive_Enable_2_>
<NAT_Keep_Alive_Msg_2_ ua="na">$NOTIFY</NAT_Keep_Alive_Msg_2_>
<NAT_Keep_Alive_Dest_2_ ua="na">$PROXY</NAT_Keep_Alive_Dest_2_>
<!-- Network Settings -->
<SIP_ToS_DiffServ_Value_2_ ua="na">0x68</SIP_ToS_DiffServ_Value_2_>
<SIP_CoS_Value_2_ ua="na">3</SIP_CoS_Value_2_>
<RTP_ToS_DiffServ_Value_2_ ua="na">0xb8</RTP_ToS_DiffServ_Value_2_>
<RTP_CoS_Value_2_ ua="na">6</RTP_CoS_Value_2_>
<Network_Jitter_Level_2_ ua="na">high</Network_Jitter_Level_2_> <!-- options: low/medium/high/very high/extremely high -->
<Jitter_Buffer_Adjustment_2_ ua="na">Yes</Jitter_Buffer_Adjustment_2_>
<!-- SIP Settings -->
<SIP_Transport_2_ ua="na">UDP</SIP_Transport_2_> <!-- options: UDP/TCP/TLS -->
<SIP_Port_2_ ua="na">5061</SIP_Port_2_>
<SIP_100REL_Enable_2_ ua="na">No</SIP_100REL_Enable_2_>
<EXT_SIP_Port_2_ ua="na"></EXT_SIP_Port_2_>
<Auth_Resync-Reboot_2_ ua="na">Yes</Auth_Resync-Reboot_2_>
<SIP_Proxy-Require_2_ ua="na"></SIP_Proxy-Require_2_>
<SIP_Remote-Party-ID_2_ ua="na">Yes</SIP_Remote-Party-ID_2_>
<SIP_GUID_2_ ua="na">No</SIP_GUID_2_>
<SIP_Debug_Option_2_ ua="na">none</SIP_Debug_Option_2_> <!-- options: none/1-line/1-line excl. OPT/1-line excl. NTFY/1-line excl. REG/1-line excl. OPT|NTFY|REG/full/full excl. OPT/full excl. NTFY/full excl. REG/full excl. OPT|NTFY|REG -->
<RTP_Log_Intvl_2_ ua="na">0</RTP_Log_Intvl_2_>
<Restrict_Source_IP_2_ ua="na">No</Restrict_Source_IP_2_>
<Referor_Bye_Delay_2_ ua="na">4</Referor_Bye_Delay_2_>
<Refer_Target_Bye_Delay_2_ ua="na">0</Refer_Target_Bye_Delay_2_>
<Referee_Bye_Delay_2_ ua="na">0</Referee_Bye_Delay_2_>
<Refer-To_Target_Contact_2_ ua="na">No</Refer-To_Target_Contact_2_>
<Sticky_183_2_ ua="na">No</Sticky_183_2_>
<Auth_INVITE_2_ ua="na">No</Auth_INVITE_2_>
<Reply_182_On_Call_Waiting_2_ ua="na">No</Reply_182_On_Call_Waiting_2_>
<Use_Anonymous_With_RPID_2_ ua="na">Yes</Use_Anonymous_With_RPID_2_>
<Use_Local_Addr_In_FROM_2_ ua="na">No</Use_Local_Addr_In_FROM_2_>
<!-- Call Feature Settings -->
<Blind_Attn-Xfer_Enable_2_ ua="na">No</Blind_Attn-Xfer_Enable_2_>
<MOH_Server_2_ ua="na"></MOH_Server_2_>
<Xfer_When_Hangup_Conf_2_ ua="na">Yes</Xfer_When_Hangup_Conf_2_>
<Conference_Bridge_URL_2_ ua="na"></Conference_Bridge_URL_2_>
<Conference_Bridge_Ports_2_ ua="na">3</Conference_Bridge_Ports_2_> <!-- options: 3/4/5/6/7/8/9/10 -->
<Enable_IP_Dialing_2_ ua="na">No</Enable_IP_Dialing_2_>
<Emergency_Number_2_ ua="na"></Emergency_Number_2_>
<Mailbox_ID_2_ ua="na"></Mailbox_ID_2_>
<!-- Proxy and Registration -->
<Proxy_2_ ua="na">%TF_SIPSERVER%</Proxy_2_>
<Outbound_Proxy_2_ ua="na">%TF_SIPSERVER%</Outbound_Proxy_2_>
<Use_Outbound_Proxy_2_ ua="na">No</Use_Outbound_Proxy_2_>
<Use_OB_Proxy_In_Dialog_2_ ua="na">Yes</Use_OB_Proxy_In_Dialog_2_>
<Register_2_ ua="na">Yes</Register_2_>
<Make_Call_Without_Reg_2_ ua="na">No</Make_Call_Without_Reg_2_>
<Register_Expires_2_ ua="na">3600</Register_Expires_2_>
<Ans_Call_Without_Reg_2_ ua="na">No</Ans_Call_Without_Reg_2_>
<Use_DNS_SRV_2_ ua="na">No</Use_DNS_SRV_2_>
<DNS_SRV_Auto_Prefix_2_ ua="na">No</DNS_SRV_Auto_Prefix_2_>
<Proxy_Fallback_Intvl_2_ ua="na">3600</Proxy_Fallback_Intvl_2_>
<Proxy_Redundancy_Method_2_ ua="na">Normal</Proxy_Redundancy_Method_2_> <!-- options: Normal/Based on SRV Port -->
<Mailbox_Subscribe_URL_2_ ua="na"></Mailbox_Subscribe_URL_2_>
<Mailbox_Subscribe_Expires_2_ ua="na">2147483647</Mailbox_Subscribe_Expires_2_>
<!-- Subscriber Information -->
<Display_Name_2_ ua="na"></Display_Name_2_>
<User_ID_2_ ua="na"></User_ID_2_>
<Password_2_ ua="na"></Password_2_>
<Use_Auth_ID_2_ ua="na">No</Use_Auth_ID_2_>
<Auth_ID_2_ ua="na"></Auth_ID_2_>
<Resident_Online_Number_2_ ua="na"></Resident_Online_Number_2_>
<SIP_URI_2_ ua="na"></SIP_URI_2_>
<!-- Supplementary Service Subscription -->
<Call_Waiting_Serv_2_ ua="na">Yes</Call_Waiting_Serv_2_>
<Block_CID_Serv_2_ ua="na">Yes</Block_CID_Serv_2_>
<Block_ANC_Serv_2_ ua="na">Yes</Block_ANC_Serv_2_>
<Dist_Ring_Serv_2_ ua="na">Yes</Dist_Ring_Serv_2_>
<Cfwd_All_Serv_2_ ua="na">Yes</Cfwd_All_Serv_2_>
<Cfwd_Busy_Serv_2_ ua="na">Yes</Cfwd_Busy_Serv_2_>
<Cfwd_No_Ans_Serv_2_ ua="na">Yes</Cfwd_No_Ans_Serv_2_>
<Cfwd_Sel_Serv_2_ ua="na">Yes</Cfwd_Sel_Serv_2_>
<Cfwd_Last_Serv_2_ ua="na">Yes</Cfwd_Last_Serv_2_>
<Block_Last_Serv_2_ ua="na">Yes</Block_Last_Serv_2_>
<Accept_Last_Serv_2_ ua="na">Yes</Accept_Last_Serv_2_>
<DND_Serv_2_ ua="na">Yes</DND_Serv_2_>
<CID_Serv_2_ ua="na">Yes</CID_Serv_2_>
<CWCID_Serv_2_ ua="na">Yes</CWCID_Serv_2_>
<Call_Return_Serv_2_ ua="na">Yes</Call_Return_Serv_2_>
<Call_Redial_Serv_2_ ua="na">Yes</Call_Redial_Serv_2_>
<Call_Back_Serv_2_ ua="na">Yes</Call_Back_Serv_2_>
<Three_Way_Call_Serv_2_ ua="na">Yes</Three_Way_Call_Serv_2_>
<Three_Way_Conf_Serv_2_ ua="na">Yes</Three_Way_Conf_Serv_2_>
<Attn_Transfer_Serv_2_ ua="na">Yes</Attn_Transfer_Serv_2_>
<Unattn_Transfer_Serv_2_ ua="na">Yes</Unattn_Transfer_Serv_2_>
<MWI_Serv_2_ ua="na">Yes</MWI_Serv_2_>
<VMWI_Serv_2_ ua="na">Yes</VMWI_Serv_2_>
<Speed_Dial_Serv_2_ ua="na">Yes</Speed_Dial_Serv_2_>
<Secure_Call_Serv_2_ ua="na">Yes</Secure_Call_Serv_2_>
<Referral_Serv_2_ ua="na">Yes</Referral_Serv_2_>
<Feature_Dial_Serv_2_ ua="na">Yes</Feature_Dial_Serv_2_>
<Service_Announcement_Serv_2_ ua="na">No</Service_Announcement_Serv_2_>
<Reuse_CID_Number_As_Name_2_ ua="na">Yes</Reuse_CID_Number_As_Name_2_>
<!-- Audio Configuration -->
<Preferred_Codec_2_ ua="na">G711u</Preferred_Codec_2_> <!-- options: G711u/G711a/G726-32/G729a -->
<Second_Preferred_Codec_2_ ua="na">Unspecified</Second_Preferred_Codec_2_> <!-- options: Unspecified/G711u/G711a/G726-32/G729a -->
<Third_Preferred_Codec_2_ ua="na">Unspecified</Third_Preferred_Codec_2_> <!-- options: Unspecified/G711u/G711a/G726-32/G729a -->
<Use_Pref_Codec_Only_2_ ua="na">No</Use_Pref_Codec_Only_2_>
<Use_Remote_Pref_Codec_2_ ua="na">No</Use_Remote_Pref_Codec_2_>
<Codec_Negotiation_2_ ua="na">Default</Codec_Negotiation_2_> <!-- options: Default/List All -->
<G729a_Enable_2_ ua="na">Yes</G729a_Enable_2_>
<Silence_Supp_Enable_2_ ua="na">No</Silence_Supp_Enable_2_>
<G726-32_Enable_2_ ua="na">Yes</G726-32_Enable_2_>
<Silence_Threshold_2_ ua="na">medium</Silence_Threshold_2_> <!-- options: high/medium/low -->
<FAX_V21_Detect_Enable_2_ ua="na">Yes</FAX_V21_Detect_Enable_2_>
<Echo_Canc_Enable_2_ ua="na">Yes</Echo_Canc_Enable_2_>
<FAX_CNG_Detect_Enable_2_ ua="na">Yes</FAX_CNG_Detect_Enable_2_>
<FAX_Passthru_Codec_2_ ua="na">G711a</FAX_Passthru_Codec_2_> <!-- options: G711u/G711a -->
<FAX_Codec_Symmetric_2_ ua="na">Yes</FAX_Codec_Symmetric_2_>
<DTMF_Process_INFO_2_ ua="na">Yes</DTMF_Process_INFO_2_>
<FAX_Passthru_Method_2_ ua="na">NSE</FAX_Passthru_Method_2_> <!-- options: None/NSE/ReINVITE -->
<DTMF_Process_AVT_2_ ua="na">Yes</DTMF_Process_AVT_2_>
<FAX_Process_NSE_2_ ua="na">Yes</FAX_Process_NSE_2_>
<DTMF_Tx_Method_2_ ua="na">Auto</DTMF_Tx_Method_2_> <!-- options: InBand/AVT/INFO/Auto/InBand+INFO/AVT+INFO -->
<FAX_Disable_ECAN_2_ ua="na">No</FAX_Disable_ECAN_2_>
<DTMF_Tx_Mode_2_ ua="na">Strict</DTMF_Tx_Mode_2_> <!-- options: Normal/Strict -->
<DTMF_Tx_Strict_Hold_Off_Time_2_ ua="na">70</DTMF_Tx_Strict_Hold_Off_Time_2_>
<FAX_Enable_T38_2_ ua="na">No</FAX_Enable_T38_2_>
<Hook_Flash_Tx_Method_2_ ua="na">None</Hook_Flash_Tx_Method_2_> <!-- options: None/AVT/INFO -->
<FAX_T38_Redundancy_2_ ua="na">1</FAX_T38_Redundancy_2_> <!-- options: 0/1/2/3 -->
<FAX_T38_ECM_Enable_2_ ua="na">Yes</FAX_T38_ECM_Enable_2_>
<FAX_Tone_Detect_Mode_2_ ua="na">caller or callee</FAX_Tone_Detect_Mode_2_> <!-- options: caller or callee/caller only/callee only -->
<Symmetric_RTP_2_ ua="na">No</Symmetric_RTP_2_>
<FAX_T38_Return_to_Voice_2_ ua="na">No</FAX_T38_Return_to_Voice_2_>
<!-- Dial Plan -->
<Dial_Plan_2_ ua="na">(*xx|[3469]11|0|00|[2-9]xxxxxx|1xxx[2-9]xxxxxxS0|xxxxxxxxxxxx.)</Dial_Plan_2_>
<!-- FXS Port Polarity Configuration -->
<Idle_Polarity_2_ ua="na">Forward</Idle_Polarity_2_> <!-- options: Forward/Reverse -->
<Caller_Conn_Polarity_2_ ua="na">Forward</Caller_Conn_Polarity_2_> <!-- options: Forward/Reverse -->
<Callee_Conn_Polarity_2_ ua="na">Forward</Callee_Conn_Polarity_2_> <!-- options: Forward/Reverse -->
<!-- Call Forward Settings -->
<Cfwd_All_Dest_1_ ua="rw"></Cfwd_All_Dest_1_>
<Cfwd_Busy_Dest_1_ ua="rw"></Cfwd_Busy_Dest_1_>
<Cfwd_No_Ans_Dest_1_ ua="rw"></Cfwd_No_Ans_Dest_1_>
<Cfwd_No_Ans_Delay_1_ ua="rw">20</Cfwd_No_Ans_Delay_1_>
<!-- Selective Call Forward Settings -->
<Cfwd_Sel1_Caller_1_ ua="rw"></Cfwd_Sel1_Caller_1_>
<Cfwd_Sel1_Dest_1_ ua="rw"></Cfwd_Sel1_Dest_1_>
<Cfwd_Sel2_Caller_1_ ua="rw"></Cfwd_Sel2_Caller_1_>
<Cfwd_Sel2_Dest_1_ ua="rw"></Cfwd_Sel2_Dest_1_>
<Cfwd_Sel3_Caller_1_ ua="rw"></Cfwd_Sel3_Caller_1_>
<Cfwd_Sel3_Dest_1_ ua="rw"></Cfwd_Sel3_Dest_1_>
<Cfwd_Sel4_Caller_1_ ua="rw"></Cfwd_Sel4_Caller_1_>
<Cfwd_Sel4_Dest_1_ ua="rw"></Cfwd_Sel4_Dest_1_>
<Cfwd_Sel5_Caller_1_ ua="rw"></Cfwd_Sel5_Caller_1_>
<Cfwd_Sel5_Dest_1_ ua="rw"></Cfwd_Sel5_Dest_1_>
<Cfwd_Sel6_Caller_1_ ua="rw"></Cfwd_Sel6_Caller_1_>
<Cfwd_Sel6_Dest_1_ ua="rw"></Cfwd_Sel6_Dest_1_>
<Cfwd_Sel7_Caller_1_ ua="rw"></Cfwd_Sel7_Caller_1_>
<Cfwd_Sel7_Dest_1_ ua="rw"></Cfwd_Sel7_Dest_1_>
<Cfwd_Sel8_Caller_1_ ua="rw"></Cfwd_Sel8_Caller_1_>
<Cfwd_Sel8_Dest_1_ ua="rw"></Cfwd_Sel8_Dest_1_>
<Cfwd_Last_Caller_1_ ua="rw"></Cfwd_Last_Caller_1_>
<Cfwd_Last_Dest_1_ ua="rw"></Cfwd_Last_Dest_1_>
<Block_Last_Caller_1_ ua="rw"></Block_Last_Caller_1_>
<Accept_Last_Caller_1_ ua="rw"></Accept_Last_Caller_1_>
<!-- Speed Dial Settings -->
<Speed_Dial_2_1_ ua="rw"></Speed_Dial_2_1_>
<Speed_Dial_3_1_ ua="rw">fnc=blf+sd+cp;sub=61@$PROXY;usr=61@$PROXY</Speed_Dial_3_1_>
<Speed_Dial_4_1_ ua="rw"></Speed_Dial_4_1_>
<Speed_Dial_5_1_ ua="rw"></Speed_Dial_5_1_>
<Speed_Dial_6_1_ ua="rw"></Speed_Dial_6_1_>
<Speed_Dial_7_1_ ua="rw"></Speed_Dial_7_1_>
<Speed_Dial_8_1_ ua="rw"></Speed_Dial_8_1_>
<Speed_Dial_9_1_ ua="rw"></Speed_Dial_9_1_>
<!-- Supplementary Service Settings -->
<CW_Setting_1_ ua="rw">Yes</CW_Setting_1_>
<Block_CID_Setting_1_ ua="rw">No</Block_CID_Setting_1_>
<Block_ANC_Setting_1_ ua="rw">No</Block_ANC_Setting_1_>
<DND_Setting_1_ ua="rw">No</DND_Setting_1_>
<CID_Setting_1_ ua="rw">Yes</CID_Setting_1_>
<CWCID_Setting_1_ ua="rw">Yes</CWCID_Setting_1_>
<Dist_Ring_Setting_1_ ua="rw">Yes</Dist_Ring_Setting_1_>
<Secure_Call_Setting_1_ ua="na">No</Secure_Call_Setting_1_>
<Message_Waiting_1_ ua="rw">No</Message_Waiting_1_>
<Accept_Media_Loopback_Request_1_ ua="na">automatic</Accept_Media_Loopback_Request_1_> <!-- options: never/automatic/manual -->
<Media_Loopback_Mode_1_ ua="na">source</Media_Loopback_Mode_1_> <!-- options: source/mirror -->
<Media_Loopback_Type_1_ ua="na">media</Media_Loopback_Type_1_> <!-- options: media/packet -->
<!-- Distinctive Ring Settings -->
<Ring1_Caller_1_ ua="rw"></Ring1_Caller_1_>
<Ring2_Caller_1_ ua="rw"></Ring2_Caller_1_>
<Ring3_Caller_1_ ua="rw"></Ring3_Caller_1_>
<Ring4_Caller_1_ ua="rw"></Ring4_Caller_1_>
<Ring5_Caller_1_ ua="rw"></Ring5_Caller_1_>
<Ring6_Caller_1_ ua="rw"></Ring6_Caller_1_>
<Ring7_Caller_1_ ua="rw"></Ring7_Caller_1_>
<Ring8_Caller_1_ ua="rw"></Ring8_Caller_1_>
<!-- Ring Settings -->
<Default_Ring_1_ ua="rw">1</Default_Ring_1_> <!-- options: 1/2/3/4/5/6/7/8 -->
<Default_CWT_1_ ua="rw">1</Default_CWT_1_> <!-- options: 1/2/3/4/5/6/7/8 -->
<Hold_Reminder_Ring_1_ ua="rw">8</Hold_Reminder_Ring_1_> <!-- options: 1/2/3/4/5/6/7/8/none -->
<Call_Back_Ring_1_ ua="rw">7</Call_Back_Ring_1_> <!-- options: 1/2/3/4/5/6/7/8 -->
<Cfwd_Ring_Splash_Len_1_ ua="rw">0</Cfwd_Ring_Splash_Len_1_>
<Cblk_Ring_Splash_Len_1_ ua="rw">0</Cblk_Ring_Splash_Len_1_>
<VMWI_Ring_Policy_1_ ua="na">New VM Available</VMWI_Ring_Policy_1_> <!-- options: New VM Available/New VM Becomes Available/New VM Arrives -->
<VMWI_Ring_Splash_Len_1_ ua="rw">0</VMWI_Ring_Splash_Len_1_>
<Ring_On_No_New_VM_1_ ua="na">No</Ring_On_No_New_VM_1_>
<!-- Call Forward Settings -->
<Cfwd_All_Dest_2_ ua="rw"></Cfwd_All_Dest_2_>
<Cfwd_Busy_Dest_2_ ua="rw"></Cfwd_Busy_Dest_2_>
<Cfwd_No_Ans_Dest_2_ ua="rw"></Cfwd_No_Ans_Dest_2_>
<Cfwd_No_Ans_Delay_2_ ua="rw">20</Cfwd_No_Ans_Delay_2_>
<!-- Selective Call Forward Settings -->
<Cfwd_Sel1_Caller_2_ ua="rw"></Cfwd_Sel1_Caller_2_>
<Cfwd_Sel1_Dest_2_ ua="rw"></Cfwd_Sel1_Dest_2_>
<Cfwd_Sel2_Caller_2_ ua="rw"></Cfwd_Sel2_Caller_2_>
<Cfwd_Sel2_Dest_2_ ua="rw"></Cfwd_Sel2_Dest_2_>
<Cfwd_Sel3_Caller_2_ ua="rw"></Cfwd_Sel3_Caller_2_>
<Cfwd_Sel3_Dest_2_ ua="rw"></Cfwd_Sel3_Dest_2_>
<Cfwd_Sel4_Caller_2_ ua="rw"></Cfwd_Sel4_Caller_2_>
<Cfwd_Sel4_Dest_2_ ua="rw"></Cfwd_Sel4_Dest_2_>
<Cfwd_Sel5_Caller_2_ ua="rw"></Cfwd_Sel5_Caller_2_>
<Cfwd_Sel5_Dest_2_ ua="rw"></Cfwd_Sel5_Dest_2_>
<Cfwd_Sel6_Caller_2_ ua="rw"></Cfwd_Sel6_Caller_2_>
<Cfwd_Sel6_Dest_2_ ua="rw"></Cfwd_Sel6_Dest_2_>
<Cfwd_Sel7_Caller_2_ ua="rw"></Cfwd_Sel7_Caller_2_>
<Cfwd_Sel7_Dest_2_ ua="rw"></Cfwd_Sel7_Dest_2_>
<Cfwd_Sel8_Caller_2_ ua="rw"></Cfwd_Sel8_Caller_2_>
<Cfwd_Sel8_Dest_2_ ua="rw"></Cfwd_Sel8_Dest_2_>
<Cfwd_Last_Caller_2_ ua="rw"></Cfwd_Last_Caller_2_>
<Cfwd_Last_Dest_2_ ua="rw"></Cfwd_Last_Dest_2_>
<Block_Last_Caller_2_ ua="rw"></Block_Last_Caller_2_>
<Accept_Last_Caller_2_ ua="rw"></Accept_Last_Caller_2_>
<!-- Speed Dial Settings -->
<Speed_Dial_2_2_ ua="rw"></Speed_Dial_2_2_>
<Speed_Dial_3_2_ ua="rw"></Speed_Dial_3_2_>
<Speed_Dial_4_2_ ua="rw"></Speed_Dial_4_2_>
<Speed_Dial_5_2_ ua="rw"></Speed_Dial_5_2_>
<Speed_Dial_6_2_ ua="rw"></Speed_Dial_6_2_>
<Speed_Dial_7_2_ ua="rw"></Speed_Dial_7_2_>
<Speed_Dial_8_2_ ua="rw"></Speed_Dial_8_2_>
<Speed_Dial_9_2_ ua="rw"></Speed_Dial_9_2_>
<!-- Supplementary Service Settings -->
<CW_Setting_2_ ua="rw">Yes</CW_Setting_2_>
<Block_CID_Setting_2_ ua="rw">No</Block_CID_Setting_2_>
<Block_ANC_Setting_2_ ua="rw">No</Block_ANC_Setting_2_>
<DND_Setting_2_ ua="rw">No</DND_Setting_2_>
<CID_Setting_2_ ua="rw">Yes</CID_Setting_2_>
<CWCID_Setting_2_ ua="rw">Yes</CWCID_Setting_2_>
<Dist_Ring_Setting_2_ ua="rw">Yes</Dist_Ring_Setting_2_>
<Secure_Call_Setting_2_ ua="na">No</Secure_Call_Setting_2_>
<Message_Waiting_2_ ua="rw">No</Message_Waiting_2_>
<Accept_Media_Loopback_Request_2_ ua="na">automatic</Accept_Media_Loopback_Request_2_> <!-- options: never/automatic/manual -->
<Media_Loopback_Mode_2_ ua="na">source</Media_Loopback_Mode_2_> <!-- options: source/mirror -->
<Media_Loopback_Type_2_ ua="na">media</Media_Loopback_Type_2_> <!-- options: media/packet -->
<!-- Distinctive Ring Settings -->
<Ring1_Caller_2_ ua="rw"></Ring1_Caller_2_>
<Ring2_Caller_2_ ua="rw"></Ring2_Caller_2_>
<Ring3_Caller_2_ ua="rw"></Ring3_Caller_2_>
<Ring4_Caller_2_ ua="rw"></Ring4_Caller_2_>
<Ring5_Caller_2_ ua="rw"></Ring5_Caller_2_>
<Ring6_Caller_2_ ua="rw"></Ring6_Caller_2_>
<Ring7_Caller_2_ ua="rw"></Ring7_Caller_2_>
<Ring8_Caller_2_ ua="rw"></Ring8_Caller_2_>
<!-- Ring Settings -->
<Default_Ring_2_ ua="rw">1</Default_Ring_2_> <!-- options: 1/2/3/4/5/6/7/8 -->
<Default_CWT_2_ ua="rw">1</Default_CWT_2_> <!-- options: 1/2/3/4/5/6/7/8 -->
<Hold_Reminder_Ring_2_ ua="rw">8</Hold_Reminder_Ring_2_> <!-- options: 1/2/3/4/5/6/7/8/none -->
<Call_Back_Ring_2_ ua="rw">7</Call_Back_Ring_2_> <!-- options: 1/2/3/4/5/6/7/8 -->
<Cfwd_Ring_Splash_Len_2_ ua="rw">0</Cfwd_Ring_Splash_Len_2_>
<Cblk_Ring_Splash_Len_2_ ua="rw">0</Cblk_Ring_Splash_Len_2_>
<VMWI_Ring_Policy_2_ ua="na">New VM Available</VMWI_Ring_Policy_2_> <!-- options: New VM Available/New VM Becomes Available/New VM Arrives -->
<VMWI_Ring_Splash_Len_2_ ua="rw">0</VMWI_Ring_Splash_Len_2_>
<Ring_On_No_New_VM_2_ ua="na">No</Ring_On_No_New_VM_2_>
<!-- Call Progress Tones -->
<Dial_Tone ua="na">425@-19;30(*/0/1)</Dial_Tone>
<Second_Dial_Tone ua="na">420@-19,520@-19;10(*/0/1+2)</Second_Dial_Tone>
<Outside_Dial_Tone ua="na">420@-16;10(*/0/1)</Outside_Dial_Tone>
<Prompt_Tone ua="na">520@-19,620@-19;10(*/0/1+2)</Prompt_Tone>
<Busy_Tone ua="na">425@-19;10(.48/.48/1)</Busy_Tone>
<Reorder_Tone ua="na">425@-19;10(.24/.24/1)</Reorder_Tone>
<Off_Hook_Warning_Tone ua="na">480@-10,620@0;10(.125/.125/1+2)</Off_Hook_Warning_Tone>
<Ring_Back_Tone ua="na">425@-19;*(1/4/1)</Ring_Back_Tone>
<Ring_Back_2_Tone ua="na">440@-19,480@-19;*(1/1/1+2)</Ring_Back_2_Tone>
<Confirm_Tone ua="na">600@-16;1(.25/.25/1)</Confirm_Tone>
<SIT1_Tone ua="na">985@-16,1428@-16,1777@-16;20(.380/0/1,.380/0/2,.380/0/3,0/4/0)</SIT1_Tone>
<SIT2_Tone ua="na">914@-16,1371@-16,1777@-16;20(.274/0/1,.274/0/2,.380/0/3,0/4/0)</SIT2_Tone>
<SIT3_Tone ua="na">914@-16,1371@-16,1777@-16;20(.380/0/1,.380/0/2,.380/0/3,0/4/0)</SIT3_Tone>
<SIT4_Tone ua="na">985@-16,1371@-16,1777@-16;20(.380/0/1,.274/0/2,.380/0/3,0/4/0)</SIT4_Tone>
<MWI_Dial_Tone ua="na">425@-19;2(.1/.1/1);10(*/0/1)</MWI_Dial_Tone>
<Cfwd_Dial_Tone ua="na">425@-19;2(.2/.2/1);10(*/0/1)</Cfwd_Dial_Tone>
<Holding_Tone ua="na">600@-19;15(.1/.1/1,.1/.1/1,.1/9.5/1)</Holding_Tone>
<Conference_Tone ua="na">350@-19;20(.1/.1/1,.1/9.7/1)</Conference_Tone>
<Secure_Call_Indication_Tone ua="na">397@-19,507@-19;15(0/2/0,.2/.1/1,.1/2.1/2)</Secure_Call_Indication_Tone>
<Feature_Invocation_Tone ua="na">350@-16;*(.1/.1/1)</Feature_Invocation_Tone>
<!-- Distinctive Ring Patterns -->
<Ring1_Cadence ua="na">60(1/4)</Ring1_Cadence>
<Ring2_Cadence ua="na">60(.8/.4,.8/4)</Ring2_Cadence>
<Ring3_Cadence ua="na">60(.4/.2,.4/.2,.8/4)</Ring3_Cadence>
<Ring4_Cadence ua="na">60(.3/.2,1/.2,.3/4)</Ring4_Cadence>
<Ring5_Cadence ua="na">1(.5/.5)</Ring5_Cadence>
<Ring6_Cadence ua="na">60(.2/.4,.2/.4,.2/4)</Ring6_Cadence>
<Ring7_Cadence ua="na">60(.4/.2,.4/.2,.4/4)</Ring7_Cadence>
<Ring8_Cadence ua="na">60(0.25/9.75)</Ring8_Cadence>
<!-- Distinctive Call Waiting Tone Patterns -->
<CWT1_Cadence ua="na">30(.2/.2,.2/5)</CWT1_Cadence>
<CWT2_Cadence ua="na">30(.1/.1, .1/9.7)</CWT2_Cadence>
<CWT3_Cadence ua="na">30(.1/.1, .1/.1, .1/9.7)</CWT3_Cadence>
<CWT4_Cadence ua="na">30(.1/.1,.3/.1,.1/9.3)</CWT4_Cadence>
<CWT5_Cadence ua="na">1(.5/.5)</CWT5_Cadence>
<CWT6_Cadence ua="na">30(.1/.1,.3/.2,.3/9.1)</CWT6_Cadence>
<CWT7_Cadence ua="na">30(.3/.1,.3/.1,.1/9.1)</CWT7_Cadence>
<CWT8_Cadence ua="na">2.3(.3/2)</CWT8_Cadence>
<!-- Distinctive Ring/CWT Pattern Names -->
<Ring1_Name ua="na">Bellcore-r1</Ring1_Name>
<Ring2_Name ua="na">Bellcore-r2</Ring2_Name>
<Ring3_Name ua="na">Bellcore-r3</Ring3_Name>
<Ring4_Name ua="na">Bellcore-r4</Ring4_Name>
<Ring5_Name ua="na">Bellcore-r5</Ring5_Name>
<Ring6_Name ua="na">Bellcore-r6</Ring6_Name>
<Ring7_Name ua="na">Bellcore-r7</Ring7_Name>
<Ring8_Name ua="na">Bellcore-r8</Ring8_Name>
<!-- Ring and Call Waiting Tone Spec -->
<Ring_Waveform ua="na">Sinusoid</Ring_Waveform> <!-- options: Sinusoid/Trapezoid -->
<Ring_Frequency ua="na">25</Ring_Frequency>
<Ring_Voltage ua="na">60</Ring_Voltage>
<CWT_Frequency ua="na">425@-19</CWT_Frequency>
<Synchronized_Ring ua="na">No</Synchronized_Ring>
<!-- Control Timer Values (sec) -->
<Hook_Flash_Timer_Min ua="na">.1</Hook_Flash_Timer_Min>
<Hook_Flash_Timer_Max ua="na">.9</Hook_Flash_Timer_Max>
<Callee_On_Hook_Delay ua="na">0</Callee_On_Hook_Delay>
<Reorder_Delay ua="na">5</Reorder_Delay>
<Call_Back_Expires ua="na">1800</Call_Back_Expires>
<Call_Back_Retry_Intvl ua="na">30</Call_Back_Retry_Intvl>
<Call_Back_Delay ua="na">.5</Call_Back_Delay>
<VMWI_Refresh_Intvl ua="na">0</VMWI_Refresh_Intvl>
<Interdigit_Long_Timer ua="na">10</Interdigit_Long_Timer>
<Interdigit_Short_Timer ua="na">3</Interdigit_Short_Timer>
<CPC_Delay ua="na">2</CPC_Delay>
<CPC_Duration ua="na">.5</CPC_Duration>
<!-- Vertical Service Activation Codes -->
<Call_Return_Code ua="na">*69</Call_Return_Code>
<Call_Redial_Code ua="na">*07</Call_Redial_Code>
<Blind_Transfer_Code ua="na">*98</Blind_Transfer_Code>
<Call_Back_Act_Code ua="na">*66</Call_Back_Act_Code>
<Call_Back_Deact_Code ua="na">*86</Call_Back_Deact_Code>
<Call_Back_Busy_Act_Code ua="na">*05</Call_Back_Busy_Act_Code>
<Cfwd_All_Act_Code ua="na">*72</Cfwd_All_Act_Code>
<Cfwd_All_Deact_Code ua="na">*73</Cfwd_All_Deact_Code>
<Cfwd_Busy_Act_Code ua="na">*90</Cfwd_Busy_Act_Code>
<Cfwd_Busy_Deact_Code ua="na">*91</Cfwd_Busy_Deact_Code>
<Cfwd_No_Ans_Act_Code ua="na">*92</Cfwd_No_Ans_Act_Code>
<Cfwd_No_Ans_Deact_Code ua="na">*93</Cfwd_No_Ans_Deact_Code>
<Cfwd_Last_Act_Code ua="na">*63</Cfwd_Last_Act_Code>
<Cfwd_Last_Deact_Code ua="na">*83</Cfwd_Last_Deact_Code>
<Block_Last_Act_Code ua="na">*60</Block_Last_Act_Code>
<Block_Last_Deact_Code ua="na">*80</Block_Last_Deact_Code>
<Accept_Last_Act_Code ua="na">*64</Accept_Last_Act_Code>
<Accept_Last_Deact_Code ua="na">*84</Accept_Last_Deact_Code>
<CW_Act_Code ua="na">*56</CW_Act_Code>
<CW_Deact_Code ua="na">*57</CW_Deact_Code>
<CW_Per_Call_Act_Code ua="na">*71</CW_Per_Call_Act_Code>
<CW_Per_Call_Deact_Code ua="na">*70</CW_Per_Call_Deact_Code>
<Block_CID_Act_Code ua="na">*67</Block_CID_Act_Code>
<Block_CID_Deact_Code ua="na">*68</Block_CID_Deact_Code>
<Block_CID_Per_Call_Act_Code ua="na">*81</Block_CID_Per_Call_Act_Code>
<Block_CID_Per_Call_Deact_Code ua="na">*82</Block_CID_Per_Call_Deact_Code>
<Block_ANC_Act_Code ua="na">*77</Block_ANC_Act_Code>
<Block_ANC_Deact_Code ua="na">*87</Block_ANC_Deact_Code>
<DND_Act_Code ua="na">*78</DND_Act_Code>
<DND_Deact_Code ua="na">*79</DND_Deact_Code>
<CID_Act_Code ua="na">*65</CID_Act_Code>
<CID_Deact_Code ua="na">*85</CID_Deact_Code>
<CWCID_Act_Code ua="na">*25</CWCID_Act_Code>
<CWCID_Deact_Code ua="na">*45</CWCID_Deact_Code>
<Dist_Ring_Act_Code ua="na">*26</Dist_Ring_Act_Code>
<Dist_Ring_Deact_Code ua="na">*46</Dist_Ring_Deact_Code>
<Speed_Dial_Act_Code ua="na">*74</Speed_Dial_Act_Code>
<Paging_Code ua="na">*96</Paging_Code>
<Secure_All_Call_Act_Code ua="na">*16</Secure_All_Call_Act_Code>
<Secure_No_Call_Act_Code ua="na">*17</Secure_No_Call_Act_Code>
<Secure_One_Call_Act_Code ua="na">*18</Secure_One_Call_Act_Code>
<Secure_One_Call_Deact_Code ua="na">*19</Secure_One_Call_Deact_Code>
<Conference_Act_Code ua="na"></Conference_Act_Code>
<Attn-Xfer_Act_Code ua="na"></Attn-Xfer_Act_Code>
<Modem_Line_Toggle_Code ua="na">*99</Modem_Line_Toggle_Code>
<FAX_Line_Toggle_Code ua="na">#99</FAX_Line_Toggle_Code>
<Media_Loopback_Code ua="na">*03</Media_Loopback_Code>
<Referral_Services_Codes ua="na"></Referral_Services_Codes>
<Feature_Dial_Services_Codes ua="na"></Feature_Dial_Services_Codes>
<!-- Vertical Service Announcement Codes -->
<Service_Annc_Base_Number ua="na"></Service_Annc_Base_Number>
<Service_Annc_Extension_Codes ua="na"></Service_Annc_Extension_Codes>
<!-- Outbound Call Codec Selection Codes -->
<Prefer_G711u_Code ua="na">*017110</Prefer_G711u_Code>
<Force_G711u_Code ua="na">*027110</Force_G711u_Code>
<Prefer_G711a_Code ua="na">*017111</Prefer_G711a_Code>
<Force_G711a_Code ua="na">*027111</Force_G711a_Code>
<Prefer_G726r32_Code ua="na">*0172632</Prefer_G726r32_Code>
<Force_G726r32_Code ua="na">*0272632</Force_G726r32_Code>
<Prefer_G729a_Code ua="na">*01729</Prefer_G729a_Code>
<Force_G729a_Code ua="na">*02729</Force_G729a_Code>
<!-- Miscellaneous -->
<FXS_Port_Impedance ua="na">220+820||115nF</FXS_Port_Impedance> <!-- options: 600/900/600+2.16uF/900+2.16uF/270+750||150nF/220+820||120nF/220+820||115nF/370+620||310nF -->
<FXS_Port_Input_Gain ua="na">-3</FXS_Port_Input_Gain>
<FXS_Port_Output_Gain ua="na">-3</FXS_Port_Output_Gain>
<DTMF_Playback_Level ua="na">-16</DTMF_Playback_Level>
<DTMF_Playback_Length ua="na">.1</DTMF_Playback_Length>
<Detect_ABCD ua="na">Yes</Detect_ABCD>
<Playback_ABCD ua="na">Yes</Playback_ABCD>
<Caller_ID_Method ua="na">Bellcore(N.Amer,China)</Caller_ID_Method> <!-- options: Bellcore(N.Amer,China)/DTMF(Finland,Sweden)/DTMF(Denmark)/ETSI DTMF/ETSI DTMF With PR/ETSI DTMF After Ring/ETSI FSK/ETSI FSK With PR(UK)/DTMF(Denmark) With PR -->
<Caller_ID_FSK_Standard ua="na">v.23</Caller_ID_FSK_Standard> <!-- options: bell 202/v.23 -->
<Feature_Invocation_Method ua="na">Default</Feature_Invocation_Method> <!-- options: Default/Sweden -->
<!-- DMZ Settings -->
<!-- Miscellaneous Settings -->
<!-- System Reserved Ports Range -->
<Protect_IVR_FactoryReset ua="na">Yes</Protect_IVR_FactoryReset>
</flat-profile>
</device>