Anleitungen

Bedienungsanleitung:
Yealink Seite

Weitere auf der Webseite verfügbare Dokumente:

Webseite:
http://www.yealink.com/

Funktionen am Telefon

  • Default Admin PIN: keine

  • Ermittlung MAC Adresse und IP:
    OK Taste drücken
  • Neustart Prozedur:
    keine

Webinterface

  • Das Webinterface des Telefons wird mit folgendem Link erreicht:
    http://<ip-adress-des-Telefons>
  • Kennwort nach Factory Reset:
    admin
  • Neustart Prozedur:
    Settings-> Rechts Reiter Starten -> Neustart -> OK
  • Eintrag des Provisionierungs-Servers

    Settings-> Rechts Reiter Automatische Einrichtung ->  URL: Server eintragen, z. B. https://www.teamsip.com/yealink -> Bestätigen -> Sofortiges Autoprovisioning Start

Anleitung zur manuellen Konfiguration

noch keine Anleitung vorhanden.

Funktionsumfang

Das Telefon unterstützt folgende Leistungsmerkmale mit Firmware Version

Firmware Version:  35.73.0.40

Leistungsmerkmal
Verfügbar
Bemerkung
1. Provisionierung  
1.1 Power over Ethernetja 
1.2 http Unterstützungja

1.3 https Unterstützung:ja 
1.4 Automatisches Konfigurationsupdate noch nicht getestet
1.5 Firmware UpdatejaÜber Download Link in u. a. Provisionierungs Beispiel.
1.6 Automatische Zeiteinstellungja 
1.7 Registration Timerja 
1.8 DTMF RFC2833ja 
1.9 Signalisierung UDPja 

1.10 Signalisierung TCP

 noch nicht getestet
1.11 Signalisierung TLS noch nicht getestet

1.12 Verschlüsselung Sprachkanal mit SRTP

 noch nicht getestet
1.13 Passwortschutz Weboberflächeja 
2. Funktionstasten  
2.1 Lautstärkeja 
2.2 Stummschaltungja 
2.3 Lauthörenja 
2.4 Bestätigenja 
2.5 Abbrechenja 
2.6 Headsetja 
2.7 Nicht störenjaals programmierbare Taste unterhalb Display
2.8 WahlwiederholungjaRedial zweimal drücken
2.9 Rufumleitungjaals programmierbare Taste unterhalb Display
2.10 BLF Tasten Statusja 
2.11 BLF Tasten Übernahmeja 
2.12 BLF Tasten Kurzwahlja 
2.13 Anruflistenja 
3. Basisfunktionen  
3.1 Codec Unterstützungja

G.722, G.711(A/μ), G.723.1, G.729AB, G.726, GSM, iLBC

3.2 Rufnummern Anzeigeja 
3.3 Rufnummern Anzeige nach Verbinden / Pickupja 
3.4 Wahl bei aufgelegtem HörerjaNummer wählen, OK
3.5 Anzeige GesprächsdauerjaDisplay oben rechts
3.6 AnklopfenjaAnklopfendes Gespräch annehmen mit "Antworten" unterhalb Display
3.7 MakelnjaTeilnehmer am Touch Display auswählen und "zurückholen" Drücken
3.8 Dreier-Konferenzja

Ersten Anruf aufbauen, zweiten Anruf annehmen und Halten. Taste "Konferenz" drücken.

3.9 Weiterleitung mit Rückfrageja

Anruf annehmen, Kurzwahltaste drücken, sprechen und dann "Weiterleiten" drücken bzw. auflegen.
Oder: "Weiterleiten" drücken, Nummer wählen und OK, sprechen, "Weiterleiten" erneut drücken oder Auflegen.

3.10 Weiterleitung ohne Rückfrageja

Anruf annehmen. Kurzwahltaste drücken und "Weiterleiten" drücken.
Oder: "Weiterleiten", Nummer eintippen und "Weiterleiten" nochmals drücken.

3.11 Rückruf bei BesetztjaKann als Yealink Funktion am Telefon programmiert werden.
3.12 Gespräch länger 30 Minutenja 
4. Zusatzfunktionen  
4.1 verschiedene KlingeltönejaSettings -> Rufton
4.2 Eigene Klingeltöneneinnicht über die Weboberfläche
4.3 Vollduplex-Freisprechenja 
4.5 Selbstbeschriftende Tastenja 
4.6 XML-Anwendungenjanicht getestet
5. Telefonbuch  
5.1 Telefonbuch am Telefonja

5.2 Telefonbuch über LDAPja

Für LDAP konfigurierte "Kontakte" Taste unterhab Display, ggf. Zurück drücken.

5.3 Telefonbuch über xml  
6. Anrufbeantworter  
6.1 MWI - Message Waiting IndicatorjaAm Display und als blinkende Lampe am Telefon.
7. Headset  
7.1 Kabelheadsets ja 
7.2 EHS HeadsetsjaPlantronics W740 mit Schnurlos Headset und Annahmeknopf am Hörer, Einrasthebel auf A an Basisstation.
Verbindungskabel siehe Plantronics EHS und Yealink
8. Erweiterungsmodule  
8.1 Funktionstasten Erweiterungsmodulja 
9. TeamSIP Funktionen  
9.1 Rufumleitung in TeamSIPja 
9.2 Persönliches Telefonbuch aus TeamSIPjaAnzeige der Kontakte über LDAP
9.3 Globales Telefonbuch aus TeamsipjaAnzeige der Kontakte über LDAP
9.4 Callcenter Anmeldung mit Status Anzeigeja

9.5 Neustart über SIP Notifyja

sip notify tiptel-reboot-cfg  10001905a
[tiptel-reboot-cfg]
Event=>check-sync\;reboot=true

9.6 Reload über SIP Notify 

noch nicht getestet

9.7 Klingelton Unterscheidung intern/extern 

distinctive_ring_tones.alert_info.1.text = Intern
distinctive_ring_tones.alert_info.1.ringer = 6

TeamSIP Provisionierungs Template

Nutzbare Tasten

Unten aufgeführtes Beispiel nutzt 46 belegbare Tasten in der TeamSIP Weboberfläche, hier mit Unterstützung Erweiterungsmodul.

Am Telefon nutzbar sind die Tasten neben dem Display und mit Ebenen Umschalt-Taste.

Konfigurationsbeispiel

Das geteste Telefon wurde mit dieser Provisionierungsvorlage als Telefon in TeamSIP konfiguriert:

TeamSIP Telefon Template

#!version:1.0.0.1

##File header "#!version:1.0.0.1" can not be edited or deleted, and must be placed in the first line.##
##This template file is applicable to SIP-T28P/T26P/T22P/T20P/T21P/T19P/T46G/T42G/T41P IP phones running firmware version 72 or later.##
##For more information on configuration parameters, refer to Yealink_SIP-T2_Series_T19P_T4_Series_IP_Phones_Auto_Provisioning_Guide.##


##manuell
phone_setting.talk_and_dial_power_led_enable = 1


##Lautstärke Hörer
voice.handset.spk_vol = 15


### Textlänge 0=Standard 1=erweitert
features.config_dsskey_length = 1


### Datumsformat
local_time.date_format = 5


### interner Klingelton aktivieren
account.1.alert_info_url_enable = 1


### TFCUST-110962
features.direct_ip_call_enable = 0
account.1.sip_trust_ctrl = 1  


#######################################################################################
## Account1 Basic Settings ## 
#######################################################################################
account.1.enable = 1
account.1.label = %TF_NUMMER%
account.1.display_name = %TF_NUMMER%
account.1.auth_name = %TF_ACCOUNT%
account.1.user_name = %TF_ACCOUNT%
account.1.password = %TF_PASSWORD%
account.1.sip_server_host = %TF_SIPSERVER%
account.1.sip_server_port = 5060
account.1.outbound_proxy_enable = 0
account.1.outbound_host = 
account.1.outbound_port = 5060
account.1.transport = 0
account.1.backup_outbound_host = 
account.1.backup_outbound_port = 5060
account.1.proxy_require = 
account.1.anonymous_call = 0
account.1.reject_anonymous_call = 0
account.1.expires = 900
account.1.sip_listen_port = 5060
account.1.100rel_enable = 0
account.1.precondition = 0
# 
account.1.cid_source = 2
account.1.session_timer.enable = 0
account.1.session_timer.expires = 
account.1.session_timer.refresher = 0
account.1.enable_user_equal_phone = 0
account.1.srtp_encryption = 0
account.1.ptime = 0
account.1.shared_line = 
account.1.dialoginfo_callpickup = 
account.1.dtmf.type = 1
account.1.dtmf.info_type = 0
account.1.dtmf.dtmf_payload = 101
account.1.nat.nat_traversal = 0
account.1.nat.stun_server = stun.teamfon.com
account.1.nat.stun_port = 10000
account.1.nat.udp_update_enable = 1
account.1.nat.udp_update_time = 30
account.1.nat.rport = 0
account.1.advanced.timer_t1 = 2
account.1.advanced.timer_t2 = 4
account.1.advanced.timer_t4 = 5
account.1.blf.subscribe_period = 3600
account.1.blf.blf_list_uri = 
account.1.codec.1.enable = 1
account.1.codec.1.payload_type = PCMU
account.1.codec.1.priority = 3
account.1.codec.1.rtpmap = 0
account.1.codec.2.enable = 1
account.1.codec.2.payload_type = PCMA
account.1.codec.2.priority = 2
account.1.codec.2.rtpmap = 8
account.1.codec.3.enable = 0
account.1.codec.3.payload_type = G723_53
account.1.codec.3.priority = 0
account.1.codec.3.rtpmap = 4
account.1.codec.4.enable = 0
account.1.codec.4.payload_type = G723_63
account.1.codec.4.priority = 0
account.1.codec.4.rtpmap = 4
account.1.codec.5.enable = 0
account.1.codec.5.payload_type = G729
account.1.codec.5.priority = 3
account.1.codec.5.rtpmap = 18
account.1.codec.6.enable = 1
account.1.codec.6.payload_type = G722
account.1.codec.6.priority = 1
account.1.codec.6.rtpmap = 9
account.1.codec.7.enable = 0
account.1.codec.7.payload_type = iLBC
account.1.codec.7.priority = 0
account.1.codec.7.rtpmap = 102
account.1.codec.8.enable = 0
account.1.codec.8.payload_type = G726-16
account.1.codec.8.priority = 0
account.1.codec.8.rtpmap = 112
account.1.codec.9.enable = 0
account.1.codec.9.payload_type = G726-24
account.1.codec.9.priority = 0
account.1.codec.9.rtpmap = 102
account.1.codec.10.enable = 0
account.1.codec.10.payload_type = G726-32
account.1.codec.10.priority = 0
account.1.codec.10.rtpmap = 2
account.1.codec.11.enable = 0
account.1.codec.11.payload_type = G726-40
account.1.codec.11.priority = 0
account.1.codec.11.rtpmap = 104
# 
network.internet_port.type = 0
network.internet_port.ip = 
network.internet_port.mask = 
network.internet_port.gateway = 
network.primary_dns = 
network.secondary_dns = 
network.pppoe.user = 
network.pppoe.password = 
network.bridge_mode = 1
network.pc_port.ip = 10.0.0.1
network.pc_port.mask = 255.255.255.0
network.pc_port.dhcp_server = 1
network.dhcp.start_ip = 10.0.0.10
network.dhcp.end_ip = 10.0.0.100
network.vlan.internet_port_enable = 0
network.vlan.internet_port_vid = 0
network.vlan.internet_port_priority = 0
network.vlan.pc_port_enable = 0
network.vlan.pc_port_vid = 0
network.vlan.pc_port_priority = 0
network.qos.signaltos = 40
network.qos.rtptos = 40
network.port.max_rtpport = 11800
network.port.min_rtpport = 11780

# syslog note
#syslog.server = 

# 
lang.gui = German
lang.wui = German

# 
local_time.time_zone = +1
local_time.time_zone_name = Germany(Berlin)
local_time.ntp_server1 = %TF_SIPSERVER%
local_time.ntp_server2 = ntp.tmwr.de

# 
phone_setting.inter_digit_time = 4
phone_setting.flash_hook_timer = 1
phone_setting.lock = 0
phone_setting.ring_type = 
phone_setting.contrast = 2
phone_setting.active_backlight_level = 10
phone_setting.backlight_time = 1800
phone_setting.product_name = 


# 
distinctive_ring_tones.alert_info.1.text = Intern
distinctive_ring_tones.alert_info.1.ringer = %TF_ALERT_INTERN%

# 
call_waiting.enable = 1

# 
features.hotline_number = 
features.busy_tone_delay = 
features.key_tone = 0
features.pound_key.mode = 1

# 
phone_setting.emergency.number = 110,112




#######################################################################################
## Transfer ## 
#######################################################################################

transfer.semi_attend_tran_enable = 1
transfer.blind_tran_on_hook_enable = 0
transfer.tran_others_after_conf_enable = 0
transfer.on_hook_trans_enable = 1
transfer.dsskey_deal_type = 1
transfer.multi_call_trans_enable = 




# 
#######################################################################################
## Line Key ## 
#######################################################################################
###Except T19D Model
###T21D/T20P X ranges from 1 to 2
###T22P/T26P X ranges from 1 to 3
###T28P X ranges from 1 to 6
###T41P/T42G X ranges from 1 to 15
###T46G X ranges from 1 to 27
#memorykey.1.sub_type = BLF
#memorykey.1.line = 0
#memorykey.1.value = %TF_NTNUMMER_1%
#memorykey.1.pickup_value = **
#memorykey.1.type = 16
#memorykey.1.label = %TF_NTNAME_1%


linekey.2.sub_type = BLF
linekey.2.line = 0
linekey.2.value = %TF_NTNUMMER_1%
linekey.2.pickup_value = **
linekey.2.type = 16
linekey.2.label = %TF_NTNAME_1%

linekey.3.sub_type = BLF
linekey.3.line = 0
linekey.3.value = %TF_NTNUMMER_2%
linekey.3.pickup_value = **
linekey.3.type = 16
linekey.3.label = %TF_NTNAME_2%

linekey.4.sub_type = BLF
linekey.4.line = 0
linekey.4.value = %TF_NTNUMMER_3%
linekey.4.pickup_value = **
linekey.4.type = 16
linekey.4.label = %TF_NTNAME_3%

linekey.5.sub_type = BLF
linekey.5.line = 0
linekey.5.value = %TF_NTNUMMER_4%
linekey.5.pickup_value = **
linekey.5.type = 16
linekey.5.label = %TF_NTNAME_4%

linekey.6.sub_type = BLF
linekey.6.line = 0
linekey.6.value = %TF_NTNUMMER_5%
linekey.6.pickup_value = **
linekey.6.type = 16
linekey.6.label = %TF_NTNAME_5%

linekey.7.sub_type = BLF
linekey.7.line = 0
linekey.7.value = %TF_NTNUMMER_6%
linekey.7.pickup_value = **
linekey.7.type = 16
linekey.7.label = %TF_NTNAME_6%

linekey.8.sub_type = BLF
linekey.8.line = 0
linekey.8.value = %TF_NTNUMMER_7%
linekey.8.pickup_value = **
linekey.8.type = 16
linekey.8.label = %TF_NTNAME_7%

linekey.9.sub_type = BLF
linekey.9.line = 0
linekey.9.value = %TF_NTNUMMER_8%
linekey.9.pickup_value = **
linekey.9.type = 16
linekey.9.label = %TF_NTNAME_8%

linekey.10.sub_type = BLF
linekey.10.line = 0
linekey.10.value = %TF_NTNUMMER_9%
linekey.10.pickup_value = **
linekey.10.type = 16
linekey.10.label = %TF_NTNAME_9%

linekey.11.sub_type = BLF
linekey.11.line = 0
linekey.11.value = %TF_NTNUMMER_10%
linekey.11.pickup_value = **
linekey.11.type = 16
linekey.11.label = %TF_NTNAME_10%


linekey.12.sub_type = BLF
linekey.12.line = 0
linekey.12.value = %TF_NTNUMMER_11%
linekey.12.pickup_value = **
linekey.12.type = 16
linekey.12.label = %TF_NTNAME_11%

linekey.13.sub_type = BLF
linekey.13.line = 0
linekey.13.value = %TF_NTNUMMER_12%
linekey.13.pickup_value = **
linekey.13.type = 16
linekey.13.label = %TF_NTNAME_12%

linekey.14.sub_type = BLF
linekey.14.line = 0
linekey.14.value = %TF_NTNUMMER_13%
linekey.14.pickup_value = **
linekey.14.type = 16
linekey.14.label = %TF_NTNAME_13%

linekey.15.sub_type = BLF
linekey.15.line = 0
linekey.15.value = %TF_NTNUMMER_14%
linekey.15.pickup_value = **
linekey.15.type = 16
linekey.15.label = %TF_NTNAME_14%

linekey.16.sub_type = BLF
linekey.16.line = 0
linekey.16.value = %TF_NTNUMMER_15%
linekey.16.pickup_value = **
linekey.16.type = 16
linekey.16.label = %TF_NTNAME_15%

linekey.17.sub_type = BLF
linekey.17.line = 0
linekey.17.value = %TF_NTNUMMER_16%
linekey.17.pickup_value = **
linekey.17.type = 16
linekey.17.label = %TF_NTNAME_16%

linekey.18.sub_type = BLF
linekey.18.line = 0
linekey.18.value = %TF_NTNUMMER_17%
linekey.18.pickup_value = **
linekey.18.type = 16
linekey.18.label = %TF_NTNAME_17%

linekey.19.sub_type = BLF
linekey.19.line = 0
linekey.19.value = %TF_NTNUMMER_18%
linekey.19.pickup_value = **
linekey.19.type = 16
linekey.19.label = %TF_NTNAME_18%

linekey.20.sub_type = BLF
linekey.20.line = 0
linekey.20.value = %TF_NTNUMMER_19%
linekey.20.pickup_value = **
linekey.20.type = 16
linekey.20.label = %TF_NTNAME_19%

linekey.21.sub_type = BLF
linekey.21.line = 0
linekey.21.value = %TF_NTNUMMER_20%
linekey.21.pickup_value = **
linekey.21.type = 16
linekey.21.label = %TF_NTNAME_20%

linekey.22.sub_type = BLF
linekey.22.line = 0
linekey.22.value = %TF_NTNUMMER_21%
linekey.22.pickup_value = **
linekey.22.type = 16
linekey.22.label = %TF_NTNAME_21%

linekey.23.sub_type = BLF
linekey.23.line = 0
linekey.23.value = %TF_NTNUMMER_22%
linekey.23.pickup_value = **
linekey.23.type = 16
linekey.23.label = %TF_NTNAME_22%

linekey.24.sub_type = BLF
linekey.24.line = 0
linekey.24.value = %TF_NTNUMMER_23%
linekey.24.pickup_value = **
linekey.24.type = 16
linekey.24.label = %TF_NTNAME_23%

linekey.25.sub_type = BLF
linekey.25.line = 0
linekey.25.value = %TF_NTNUMMER_24%
linekey.25.pickup_value = **
linekey.25.type = 16
linekey.25.label = %TF_NTNAME_24%

linekey.26.sub_type = BLF
linekey.26.line = 0
linekey.26.value = %TF_NTNUMMER_25%
linekey.26.pickup_value = **
linekey.26.type = 16
linekey.26.label = %TF_NTNAME_25%

linekey.27.sub_type = BLF
linekey.27.line = 0
linekey.27.value = %TF_NTNUMMER_26%
linekey.27.pickup_value = **
linekey.27.type = 16
linekey.27.label = %TF_NTNAME_26%

linekey.28.sub_type = BLF
linekey.28.line = 0
linekey.28.value = %TF_NTNUMMER_27%
linekey.28.pickup_value = **
linekey.28.type = 16
linekey.28.label = %TF_NTNAME_27%

#######################################################################################
## Programable Key ## 
#######################################################################################
###T20P X ranges from 1 to 9
###T28P/T26P X ranges from 1 to 14
###T41P/T42G/T19P/T21P X ranges from 1 to 11
###T46G/T22P X ranges from 1 to 13
programablekey.2.type = 38
programablekey.2.line = 0
programablekey.2.label = Kontakte
programablekey.2.line = 0
programablekey.2.xml_phonebook = 0
programablekey.2.history_type = 0

# voice note
voice.vad = 0
voice.cng = 1
voice.echo_cancellation = 1
# voice.side_tone = -3
voice.jib.adaptive = 1
voice.jib.min = 0
voice.jib.max = 300
voice.jib.normal = 120

# 
voice_mail.number.1 = *99
voice_mail.number.2 = *99
voice_mail.number.3 = *99
voice_mail.number.4 = *99
voice_mail.number.5 = *99
voice_mail.number.6 = *99

# voice note
voice.tone.country = Germany
voice.tone.dial = 
voice.tone.ring = 
voice.tone.busy = 
voice.tone.congestion = 
voice.tone.callwaiting = 
voice.tone.dialrecall = 
voice.tone.record = 
voice.tone.info = 
voice.tone.stutter = 
voice.tone.message = 
voice.tone.autoanswer = 

# ldap note
ldap.enable = 1
ldap.name_filter = (&(telNrBusiness1=*)(sn=%))
ldap.number_filter = 
ldap.host = %TF_SIPSERVER%
ldap.port = 389
ldap.base = 
ldap.user = uid=%TF_CONTEXT%%TF_NUMMER%,ou=authentication,dc=teamfom,dc=de
ldap.password = %TF_PASSWORD%
ldap.max_hits = 100
ldap.name_attr = sn cn
ldap.numb_attr = telNrBusiness1 telNrBusiness2 telNrMobile telNrPrivate
ldap.display_name = %cn
ldap.version = 3
ldap.base = ou=Teamfon,ou=userdata,ou=appls,dc=teamware,dc=de
ldap.ldap_sort = 0
ldap.call_in_lookup = 0

#
auto_provision.mode = 7
# 
auto_provision.schedule.periodic_minute = 
auto_provision.schedule.time_from = 02:00
auto_provision.schedule.time_to = 03:00
auto_provision.schedule.dayofweek = 0123456
# 
auto_provision.pnp_enable = 0
auto_provision.dhcp_option.list_user_options = 
# 
auto_provision.server.url = http://%TF_SIPSERVER%/yealink
# security note
security.user_password = admin:team05
security.user_password = user:
#


#######################################################################################
## Dial Plan ##
#######################################################################################



dialplan.area_code.code = 
dialplan.area_code.min_len = 1
dialplan.area_code.max_len = 15

dialplan.area_code.line_id =

dialplan.block_out.number.1 =

dialplan.block_out.line_id.1 =

#######################################################################################
## Firmware ##
#######################################################################################



firmware.url = http://%TF_SIPSERVER%/yealink/firmware/35.73.0.40.rom
HTML/XML