Yealink T52S
Das T52S von Yealink basiert auf dem Android Betriebssystem.
Anleitungen
Bedienungsanleitung:
Yealink Seite
Weitere auf der Webseite verfügbare Dokumente:
Webseite:
http://www.yealink.com/
Funktionen am Telefon
- Default Admin PIN: keine
- Ermittlung MAC Adresse und IP:
Auf OK Taste drücken - Neustart Prozedur:
keine Reset Prozedur:
länger als 5 Sekunden auf OK drücken, dann bestätigen
Webinterface
- Das Webinterface des Telefons wird mit folgendem Link erreicht:
http://<ip-adress-des-Telefons> - Kennwort nach Factory Reset:
admin - Neustart Prozedur:
Settings-> Rechts Reiter Starten -> Neustart -> OK - Eintrag des Provisionierungs-Servers
Settings-> Rechts Reiter Automatische Einrichtung -> URL: Server eintragen, z. B. https://www.teamsip.com/yealink -> Bestätigen -> Sofortiges Autoprovisioning Start
Anleitung zur manuellen Konfiguration
noch keine Anleitung vorhanden.
Funktionsumfang
Das Telefon unterstützt folgende Leistungsmerkmale mit Firmware Version
Firmware Version: Yealink SIP-T52S 70.81.0.10
Leistungsmerkmal | Verfügbar | Bemerkung |
|---|---|---|
| 1. Provisionierung | ||
| 1.1 Power over Ethernet | ja | |
| 1.2 http Unterstützung | ja | |
| 1.3 https Unterstützung: | ja | |
| 1.4 Automatisches Konfigurationsupdate | ja | |
| 1.5 Firmware Update | ja | Über Download Link in u. a. Provisionierungs Beispiel. |
| 1.6 Automatische Zeiteinstellung | ja | |
| 1.7 Registration Timer | ja | |
| 1.8 DTMF RFC2833 | ja | |
| 1.9 Signalisierung UDP | ja | |
1.10 Signalisierung TCP | ja | |
| 1.11 Signalisierung TLS | ja | |
1.12 Verschlüsselung Sprachkanal mit SRTP | ja | |
| 1.13 Passwortschutz Weboberfläche | ja | |
| 2. Funktionstasten | ||
| 2.1 Lautstärke | ja | |
| 2.2 Stummschaltung | ja | |
| 2.3 Lauthören | ja | |
| 2.4 Bestätigen | ja | |
| 2.5 Abbrechen | ja | Die Auflegen Taste mit rotem Hörer |
| 2.6 Headset | ja | |
| 2.7 Nicht stören | ja | als programmierbare Taste unterhalb Display |
| 2.8 Wahlwiederholung | ja | |
| 2.9 Rufumleitung | ja | als programmierbare Taste unterhalb Display |
| 2.10 BLF Tasten Status | ja | |
| 2.11 BLF Tasten Übernahme | ja | |
| 2.12 BLF Tasten Kurzwahl | ja | |
| 2.13 Anruflisten | ja | |
| 3. Basisfunktionen | ||
| 3.1 Codec Unterstützung | ja | G.722, G.711(A/μ), G.723, G.729AB, G.726, GSM, iLBC |
| 3.2 Rufnummern Anzeige | ja | |
| 3.3 Rufnummern Anzeige nach Verbinden / Pickup | ja | |
| 3.4 Wahl bei aufgelegtem Hörer | ja | Nummer wählen, OK |
| 3.5 Anzeige Gesprächsdauer | ja | Display unter Zeit |
| 3.6 Anklopfen | ja | |
| 3.7 Makeln | ja | "Wechseln" Drücken |
| 3.8 Dreier-Konferenz | ja | Ersten Anruf aufbauen, zweiten Anruf annehmen und Halten. Taste "Konferenz" drücken. |
| 3.9 Weiterleitung mit Rückfrage | ja | Anruf annehmen, "Halten", dann "Neues Gespräch aufbauen" drücken, Nummer wählen, sprechen und dann "Weiterleiten" drücken. |
| 3.10 Weiterleitung ohne Rückfrage | ja | Anruf annehmen. "Weiterleiten" drücken und "Weiterleiten" drücken. |
| 3.11 Rückruf bei Besetzt | ja | Kann als Yealink Funktion am Telefon programmiert werden. |
| 3.12 Gespräch länger 30 Minuten | ja | |
| 4. Zusatzfunktionen | ||
| 4.1 verschiedene Klingeltöne | ja | Settings -> Rufton |
| 4.2 Eigene Klingeltöne | nein | nicht über die Weboberfläche |
| 4.3 Vollduplex-Freisprechen | ja | |
| 4.5 Selbstbeschriftende Tasten | ja | |
| 4.6 XML-Anwendungen | ja | nicht getestet |
| 5. Telefonbuch | ||
| 5.1 Telefonbuch am Telefon | ja | |
| 5.2 Telefonbuch über LDAP | ja | Für LDAP konfigurierte "Kontakte" Taste unterhab Display, ggf. Zurück drücken. |
| 5.3 Telefonbuch über xml | ||
| 6. Anrufbeantworter | ||
| 6.1 MWI - Message Waiting Indicator | ja | Am Display und als Meldung und Symbol. |
| 7. Headset | ||
| 7.1 Kabelheadsets | ja | |
| 7.2 EHS Headsets | ja | |
| 8. Erweiterungsmodule | ||
| 8.1 Funktionstasten Erweiterungsmodul | ja | Je nach Modell |
| 9. TeamSIP Funktionen | ||
| 9.1 Rufumleitung in TeamSIP | ja | |
| 9.2 Persönliches Telefonbuch aus TeamSIP | ja | Anzeige der Kontakte über LDAP |
| 9.3 Globales Telefonbuch aus Teamsip | ja | Anzeige der Kontakte über LDAP |
| 9.4 Callcenter Anmeldung mit Status Anzeige | ja | |
| 9.5 Neustart über SIP Notify | ja | sip notify yealink-reboot-cfg 10001909a [yealink-reboot-cfg] |
| 9.6 Reload über SIP Notify | ja | |
| 9.7 Klingelton Unterscheidung intern/extern | ja | distinctive_ring_tones.alert_info.1.text = Intern |
TeamSIP Provisionierungs Template
Nutzbare Tasten
Unten aufgeführtes Beispiel nutzt 28 belegbare Tasten in der TeamSIP Weboberfläche, hier mit Unterstützung Erweiterungsmodul.
Am Telefon nutzbar sind die Tasten neben dem Display und mit Ebenen Umschalt-Taste.
Konfigurationsbeispiel
Parameter für dieses Template:
| Name | Vorgabe |
|---|---|
| TF_FIRMWARE | T54S_T52S_70.81.0.10.rom |
| TF_TRANSPORT | 0 |
| TF_SERVERPORT | 5060 |
| TF_INTERN_LAENGE | xx |
| TF_ALERT_INTERN | 6 |
| TF_VORWAHL | 089 |
| TF_LOGO_PATH | http://berlix2-lb1.teamfon.com/images/ |
| TF_LOGO_FILE | teamfon_ybg_black.jpg |
| TF_KEYLENGTH | 0 |
Das geteste Telefon wurde mit dieser Provisionierungsvorlage als Telefon in TeamSIP konfiguriert:
TeamSIP Telefon Template
#!version:1.0.0.1
##File header "#!version:1.0.0.1" can not be edited or deleted, and must be placed in the first line.##
##This template file is applicable to SIP-T28P/T26P/T22P/T20P/T21P/T19P/T46G/T42G/T41P IP phones running firmware version 72 or later.##
##For more information on configuration parameters, refer to Yealink_SIP-T2_Series_T19P_T4_Series_IP_Phones_Auto_Provisioning_Guide.##
##manuell
phone_setting.talk_and_dial_power_led_enable = 1
##Lautstärke Hörer
voice.handset.spk_vol = 15
### Textlänge 0=Standard 1=erweitert
features.config_dsskey_length = %TF_KEYLENGTH%
### Datumsformat
local_time.date_format = 5
### interner Klingelton aktivieren
account.1.alert_info_url_enable = 1
distinctive_ring_tones.alert_info.1.text = Intern
distinctive_ring_tones.alert_info.1.ringer = %TF_ALERT_INTERN%
### TFCUST-110962
features.direct_ip_call_enable = 0
account.1.sip_trust_ctrl = 1
#######################################################################################
## Account1 Basic Settings ##
#######################################################################################
account.1.enable = 1
account.1.label = %TF_NUMMER%
account.1.display_name = %TF_NUMMER%
account.1.auth_name = %TF_ACCOUNT%
account.1.user_name = %TF_ACCOUNT%
account.1.password = %TF_PASSWORD%
account.1.sip_server_host = %TF_SIPSERVER%
account.1.sip_server_port = %TF_SERVERPORT%
account.1.sip_server_type = 0
account.1.outbound_proxy_enable = 0
account.1.outbound_host =
account.1.outbound_port = %TF_SERVERPORT%
account.1.transport = %TF_TRANSPORT%
account.1.backup_outbound_host =
account.1.backup_outbound_port = %TF_SERVERPORT%
account.1.proxy_require =
account.1.anonymous_call = 0
account.1.reject_anonymous_call = 0
account.1.expires = 900
account.1.sip_listen_port = %TF_SERVERPORT%
account.1.100rel_enable = 0
account.1.precondition = 0
#
account.1.cid_source = 2
account.1.session_timer.enable = 0
account.1.session_timer.expires =
account.1.session_timer.refresher = 0
account.1.enable_user_equal_phone = 0
account.1.srtp_encryption = 0
account.1.ptime = 0
account.1.shared_line =
account.1.dialoginfo_callpickup =
account.1.dtmf.type = 1
account.1.dtmf.info_type = 0
account.1.dtmf.dtmf_payload = 101
account.1.nat.nat_traversal = 0
account.1.nat.stun_server = stun.teamfon.com
account.1.nat.stun_port = 10000
account.1.nat.udp_update_enable = 1
account.1.nat.udp_update_time = 30
account.1.nat.rport = 0
account.1.advanced.timer_t1 = 2
account.1.advanced.timer_t2 = 4
account.1.advanced.timer_t4 = 5
account.1.blf.subscribe_period = 3600
account.1.blf.blf_list_uri =
account.1.codec.1.enable = 1
account.1.codec.1.payload_type = PCMU
account.1.codec.1.priority = 3
account.1.codec.1.rtpmap = 0
account.1.codec.2.enable = 1
account.1.codec.2.payload_type = PCMA
account.1.codec.2.priority = 2
account.1.codec.2.rtpmap = 8
account.1.codec.3.enable = 0
account.1.codec.3.payload_type = G723_53
account.1.codec.3.priority = 0
account.1.codec.3.rtpmap = 4
account.1.codec.4.enable = 0
account.1.codec.4.payload_type = G723_63
account.1.codec.4.priority = 0
account.1.codec.4.rtpmap = 4
account.1.codec.5.enable = 0
account.1.codec.5.payload_type = G729
account.1.codec.5.priority = 3
account.1.codec.5.rtpmap = 18
account.1.codec.6.enable = 1
account.1.codec.6.payload_type = G722
account.1.codec.6.priority = 1
account.1.codec.6.rtpmap = 9
account.1.codec.7.enable = 0
account.1.codec.7.payload_type = iLBC
account.1.codec.7.priority = 0
account.1.codec.7.rtpmap = 102
account.1.codec.8.enable = 0
account.1.codec.8.payload_type = G726-16
account.1.codec.8.priority = 0
account.1.codec.8.rtpmap = 112
account.1.codec.9.enable = 0
account.1.codec.9.payload_type = G726-24
account.1.codec.9.priority = 0
account.1.codec.9.rtpmap = 102
account.1.codec.10.enable = 0
account.1.codec.10.payload_type = G726-32
account.1.codec.10.priority = 0
account.1.codec.10.rtpmap = 2
account.1.codec.11.enable = 0
account.1.codec.11.payload_type = G726-40
account.1.codec.11.priority = 0
account.1.codec.11.rtpmap = 104
#
network.internet_port.type = 0
network.internet_port.ip =
network.internet_port.mask =
network.internet_port.gateway =
network.primary_dns =
network.secondary_dns =
network.pppoe.user =
network.pppoe.password =
network.bridge_mode = 1
network.pc_port.ip = 10.0.0.1
network.pc_port.mask = 255.255.255.0
network.pc_port.dhcp_server = 1
network.dhcp.start_ip = 10.0.0.10
network.dhcp.end_ip = 10.0.0.100
network.vlan.internet_port_enable = 0
network.vlan.internet_port_vid = 0
network.vlan.internet_port_priority = 0
network.vlan.pc_port_enable = 0
network.vlan.pc_port_vid = 0
network.vlan.pc_port_priority = 0
network.qos.signaltos = 40
network.qos.rtptos = 40
network.port.max_rtpport = 11800
network.port.min_rtpport = 11780
# syslog note
#syslog.server =
#
lang.gui = German
lang.wui = German
#
local_time.time_zone = +1
local_time.time_zone_name = Germany(Berlin)
local_time.ntp_server1 = %TF_SIPSERVER%
local_time.ntp_server2 = ntp.tmwr.de
#
phone_setting.inter_digit_time = 4
phone_setting.flash_hook_timer = 1
phone_setting.lock = 0
phone_setting.ring_type =
phone_setting.contrast = 2
phone_setting.active_backlight_level = 10
phone_setting.backlight_time = 1800
phone_setting.product_name =
sip.call_fail_use_reason.enable = 0
#
call_waiting.enable = 1
#
features.hotline_number =
features.busy_tone_delay =
features.key_tone = 0
features.pound_key.mode = 1
features.dnd.large_icon.enable = 1
#
phone_setting.emergency.number = 110,112
#######################################################################################
## Transfer ##
#######################################################################################
transfer.semi_attend_tran_enable = 1
transfer.blind_tran_on_hook_enable = 0
transfer.tran_others_after_conf_enable = 0
transfer.on_hook_trans_enable =
transfer.dsskey_deal_type = 1
transfer.multi_call_trans_enable =
#
#######################################################################################
## Line Key ##
#######################################################################################
###Except T19D Model
###T21D/T20P X ranges from 1 to 2
###T22P/T26P X ranges from 1 to 3
###T28P X ranges from 1 to 6
###T41P/T42G X ranges from 1 to 15
###T46G X ranges from 1 to 27
linekey.1.line = 1
linekey.1.value = %TF_NTNUMMER_1%
linekey.1.pickup_value = **
linekey.1.type = 16
linekey.1.label = %TF_NTNAME_1%
linekey.2.line = 1
linekey.2.value = %TF_NTNUMMER_2%
linekey.2.pickup_value = **
linekey.2.type = 16
linekey.2.label = %TF_NTNAME_2%
linekey.3.line = 1
linekey.3.value = %TF_NTNUMMER_3%
linekey.3.pickup_value = **
linekey.3.type = 16
linekey.3.label = %TF_NTNAME_3%
linekey.4.sub_type = BLF
linekey.4.line = 1
linekey.4.value = %TF_NTNUMMER_4%
linekey.4.pickup_value = **
linekey.4.type = 16
linekey.4.label = %TF_NTNAME_4%
linekey.5.sub_type = BLF
linekey.5.line = 1
linekey.5.value = %TF_NTNUMMER_5%
linekey.5.pickup_value = **
linekey.5.type = 16
linekey.5.label = %TF_NTNAME_5%
linekey.6.sub_type = BLF
linekey.6.line = 1
linekey.6.value = %TF_NTNUMMER_6%
linekey.6.pickup_value = **
linekey.6.type = 16
linekey.6.label = %TF_NTNAME_6%
linekey.7.sub_type = BLF
linekey.7.line = 1
linekey.7.value = %TF_NTNUMMER_7%
linekey.7.pickup_value = **
linekey.7.type = 16
linekey.7.label = %TF_NTNAME_7%
linekey.8.sub_type = BLF
linekey.8.line = 1
linekey.8.value = %TF_NTNUMMER_8%
linekey.8.pickup_value = **
linekey.8.type = 16
linekey.8.label = %TF_NTNAME_8%
linekey.9.sub_type = BLF
linekey.9.line = 1
linekey.9.value = %TF_NTNUMMER_9%
linekey.9.pickup_value = **
linekey.9.type = 16
linekey.9.label = %TF_NTNAME_9%
linekey.10.sub_type = BLF
linekey.10.line = 1
linekey.10.value = %TF_NTNUMMER_10%
linekey.10.pickup_value = **
linekey.10.type = 16
linekey.10.label = %TF_NTNAME_10%
linekey.11.sub_type = BLF
linekey.11.line = 1
linekey.11.value = %TF_NTNUMMER_11%
linekey.11.pickup_value = **
linekey.11.type = 16
linekey.11.label = %TF_NTNAME_11%
linekey.12.sub_type = BLF
linekey.12.line = 1
linekey.12.value = %TF_NTNUMMER_12%
linekey.12.pickup_value = **
linekey.12.type = 16
linekey.12.label = %TF_NTNAME_12%
linekey.13.sub_type = BLF
linekey.13.line = 1
linekey.13.value = %TF_NTNUMMER_13%
linekey.13.pickup_value = **
linekey.13.type = 16
linekey.13.label = %TF_NTNAME_13%
linekey.14.sub_type = BLF
linekey.14.line = 1
linekey.14.value = %TF_NTNUMMER_14%
linekey.14.pickup_value = **
linekey.14.type = 16
linekey.14.label = %TF_NTNAME_14%
linekey.15.sub_type = BLF
linekey.15.line = 1
linekey.15.value = %TF_NTNUMMER_15%
linekey.15.pickup_value = **
linekey.15.type = 16
linekey.15.label = %TF_NTNAME_15%
linekey.16.sub_type = BLF
linekey.16.line = 1
linekey.16.value = %TF_NTNUMMER_16%
linekey.16.pickup_value = **
linekey.16.type = 16
linekey.16.label = %TF_NTNAME_16%
linekey.17.sub_type = BLF
linekey.17.line = 1
linekey.17.value = %TF_NTNUMMER_17%
linekey.17.pickup_value = **
linekey.17.type = 16
linekey.17.label = %TF_NTNAME_17%
linekey.18.sub_type = BLF
linekey.18.line = 1
linekey.18.value = %TF_NTNUMMER_18%
linekey.18.pickup_value = **
linekey.18.type = 16
linekey.18.label = %TF_NTNAME_18%
linekey.19.sub_type = BLF
linekey.19.line = 1
linekey.19.value = %TF_NTNUMMER_19%
linekey.19.pickup_value = **
linekey.19.type = 16
linekey.19.label = %TF_NTNAME_19%
linekey.20.sub_type = BLF
linekey.20.line = 1
linekey.20.value = %TF_NTNUMMER_20%
linekey.20.pickup_value = **
linekey.20.type = 16
linekey.20.label = %TF_NTNAME_20%
linekey.21.sub_type = BLF
linekey.21.line = 1
linekey.21.value = %TF_NTNUMMER_21%
linekey.21.pickup_value = **
linekey.21.type = 16
linekey.21.label = %TF_NTNAME_21%
linekey.22.sub_type = BLF
linekey.22.line = 1
linekey.22.value = %TF_NTNUMMER_22%
linekey.22.pickup_value = **
linekey.22.type = 16
linekey.22.label = %TF_NTNAME_22%
linekey.23.sub_type = BLF
linekey.23.line = 1
linekey.23.value = %TF_NTNUMMER_23%
linekey.23.pickup_value = **
linekey.23.type = 16
linekey.23.label = %TF_NTNAME_23%
linekey.24.sub_type = BLF
linekey.24.line = 1
linekey.24.value = %TF_NTNUMMER_24%
linekey.24.pickup_value = **
linekey.24.type = 16
linekey.24.label = %TF_NTNAME_24%
linekey.25.sub_type = BLF
linekey.25.line = 1
linekey.25.value = %TF_NTNUMMER_25%
linekey.25.pickup_value = **
linekey.25.type = 16
linekey.25.label = %TF_NTNAME_25%
linekey.26.sub_type = BLF
linekey.26.line = 1
linekey.26.value = %TF_NTNUMMER_26%
linekey.26.pickup_value = **
linekey.26.type = 16
linekey.26.label = %TF_NTNAME_26%
linekey.27.sub_type = BLF
linekey.27.line = 1
linekey.27.value = %TF_NTNUMMER_27%
linekey.27.pickup_value = **
linekey.27.type = 16
linekey.27.label = %TF_NTNAME_27%
linekey.28.sub_type = BLF
linekey.28.line = 1
linekey.28.value = %TF_NTNUMMER_28%
linekey.28.pickup_value = **
linekey.28.type = 16
linekey.28.label = %TF_NTNAME_28%
#######################################################################################
## Programable Key ##
#######################################################################################
###T20P X ranges from 1 to 9
###T28P/T26P X ranges from 1 to 14
###T41P/T42G/T19P/T21P X ranges from 1 to 11
###T46G/T22P X ranges from 1 to 13
programablekey.2.type = 38
programablekey.2.label = Kontakte
# voice note
voice.vad = 0
voice.cng = 1
voice.echo_cancellation = 1
# voice.side_tone = -3
voice.jib.adaptive = 1
voice.jib.min = 0
voice.jib.max = 300
voice.jib.normal = 120
#
voice_mail.number.1 = *99
voice_mail.number.2 = *99
voice_mail.number.3 = *99
voice_mail.number.4 = *99
voice_mail.number.5 = *99
voice_mail.number.6 = *99
# voice note
voice.tone.country = Germany
voice.tone.dial =
voice.tone.ring =
voice.tone.busy =
voice.tone.congestion =
voice.tone.callwaiting =
voice.tone.dialrecall =
voice.tone.record =
voice.tone.info =
voice.tone.stutter =
voice.tone.message =
voice.tone.autoanswer =
# ldap note
ldap.enable = 1
ldap.name_filter = (&(telNrBusiness1=*)(sn=%))
ldap.number_filter =
ldap.host = %TF_SIPSERVER%
ldap.port = 389
ldap.base =
ldap.user = uid=%TF_ACCOUNT%,ou=authentication,dc=teamfom,dc=de
ldap.password = %TF_PASSWORD%
ldap.max_hits = 100
ldap.name_attr = sn cn
ldap.numb_attr = telNrBusiness1 telNrBusiness2 telNrMobile telNrPrivate
ldap.display_name = %cn
ldap.version = 3
ldap.base = ou=Teamfon,ou=userdata,ou=appls,dc=teamware,dc=de
ldap.ldap_sort = 0
ldap.call_in_lookup = 0
#
auto_provision.mode = 7
#
auto_provision.schedule.periodic_minute =
auto_provision.schedule.time_from = 02:00
auto_provision.schedule.time_to = 03:00
auto_provision.schedule.dayofweek = 0123456
#
auto_provision.pnp_enable = 0
auto_provision.dhcp_option.list_user_options =
#
auto_provision.server.url = http://%TF_SIPSERVER%/yealink
# security note
security.user_password = admin:team%TF_CONTEXT%
security.user_password = user:
#
#######################################################################################
## Dial Plan ##
#######################################################################################
dialplan.area_code.code =
dialplan.area_code.min_len = 1
dialplan.area_code.max_len = 15
dialplan.area_code.line_id =
dialplan.block_out.number.1 =
dialplan.block_out.line_id.1 =
dialplan.item.1 = 1,([1-9]%TF_INTERN_LAENGE%.),%TF_VORWAHL%$1
#######################################################################################
## Firmware ##
#######################################################################################
firmware.url = http://%TF_SIPSERVER%/yealink/firmware/%TF_FIRMWARE%
wallpaper_upload.url = %TF_LOGO_PATH%%TF_LOGO_FILE%
phone_setting.backgrounds = Config:%TF_LOGO_FILE%
HTML/XML