Das T58V von Yealink basiert auf dem Android Betriebssystem.

Anleitungen

Bedienungsanleitung:
Yealink Seite

Weitere auf der Webseite verfügbare Dokumente:

Webseite:
http://www.yealink.com/

Funktionen am Telefon

  • Default Admin PIN: keine
  • Ermittlung MAC Adresse und IP:
    Auf OK Taste drücken
  • Neustart Prozedur:
    keine

  • Reset Prozedur:
    länger als 5 Sekunden auf OK drücken, dann bestätigen

Webinterface

  • Das Webinterface des Telefons wird mit folgendem Link erreicht:
    http://<ip-adress-des-Telefons>
  • Kennwort nach Factory Reset:
    admin
  • Neustart Prozedur:
    Settings-> Rechts Reiter Starten -> Neustart -> OK
  • Eintrag des Provisionierungs-Servers

    Settings-> Rechts Reiter Automatische Einrichtung ->  URL: Server eintragen, z. B. https://www.teamsip.com/yealink -> Bestätigen -> Sofortiges Autoprovisioning Start

Anleitung zur manuellen Konfiguration

noch keine Anleitung vorhanden.

Funktionsumfang

Das Telefon unterstützt folgende Leistungsmerkmale mit Firmware Version

Firmware Version:  58.80.0.10.rom

Leistungsmerkmal
Verfügbar
Bemerkung
1. Provisionierung  
1.1 Power over Ethernetja 
1.2 http Unterstützungja

1.3 https Unterstützung:ja 
1.4 Automatisches Konfigurationsupdateja 
1.5 Firmware UpdatejaÜber Download Link in u. a. Provisionierungs Beispiel.
1.6 Automatische Zeiteinstellungja 
1.7 Registration Timerja 
1.8 DTMF RFC2833ja 
1.9 Signalisierung UDPja 

1.10 Signalisierung TCP

ja 
1.11 Signalisierung TLSja 

1.12 Verschlüsselung Sprachkanal mit SRTP

ja 
1.13 Passwortschutz Weboberflächeja 
2. Funktionstasten  
2.1 Lautstärkeja 
2.2 Stummschaltungja 
2.3 Lauthörenja 
2.4 Bestätigenja 
2.5 AbbrechenjaDie Auflegen Taste mit rotem Hörer
2.6 Headsetja 
2.7 Nicht störenjaals programmierbare Taste unterhalb Display
2.8 Wahlwiederholungja 
2.9 Rufumleitungjaals programmierbare Taste unterhalb Display
2.10 BLF Tasten Statusja 
2.11 BLF Tasten Übernahmeja 
2.12 BLF Tasten Kurzwahlja 
2.13 Anruflistenja 
3. Basisfunktionen  
3.1 Codec Unterstützungja

G.722, G.711(A/μ), G.723, G.729AB, G.726, GSM, iLBC

3.2 Rufnummern Anzeigeja 
3.3 Rufnummern Anzeige nach Verbinden / Pickupja 
3.4 Wahl bei aufgelegtem HörerjaNummer wählen, OK
3.5 Anzeige GesprächsdauerjaDisplay unter Zeit
3.6 Anklopfenja 
3.7 Makelnja"Wechseln" Drücken
3.8 Dreier-Konferenzja

Ersten Anruf aufbauen, zweiten Anruf annehmen und Halten. Taste "Konferenz" drücken.

3.9 Weiterleitung mit Rückfrageja

Anruf annehmen, "Halten", dann "Neues Gespräch aufbauen" drücken, Nummer wählen, sprechen und dann "Weiterleiten" drücken.
Oder: "Weiterleiten" drücken, Nummer wählen und OK, sprechen, "Weiterleiten" erneut drücken oder Auflegen.

3.10 Weiterleitung ohne Rückfrageja

Anruf annehmen. "Weiterleiten" drücken und "Weiterleiten" drücken.
Oder: "Weiterleiten/Transfer", Nummer eintippen und "Weiterleiten/Transfer" nochmals drücken.

3.11 Rückruf bei BesetztjaKann als Yealink Funktion am Telefon programmiert werden.
3.12 Gespräch länger 30 Minutenja 
4. Zusatzfunktionen  
4.1 verschiedene KlingeltönejaSettings -> Rufton
4.2 Eigene Klingeltöneneinnicht über die Weboberfläche
4.3 Vollduplex-Freisprechenja 
4.5 Selbstbeschriftende Tastenja 
4.6 XML-Anwendungenjanicht getestet
5. Telefonbuch  
5.1 Telefonbuch am Telefonja

5.2 Telefonbuch über LDAPja

Für LDAP konfigurierte "Kontakte" Taste unterhab Display, ggf. Zurück drücken.

5.3 Telefonbuch über xml  
6. Anrufbeantworter  
6.1 MWI - Message Waiting IndicatorjaAm Display und als Meldung und Symbol.
7. Headset  
7.1 Kabelheadsetsja 
7.2 EHS Headsetsja 
8. Erweiterungsmodule  
8.1 Funktionstasten ErweiterungsmoduljaJe nach Modell
9. TeamSIP Funktionen  
9.1 Rufumleitung in TeamSIPja 
9.2 Persönliches Telefonbuch aus TeamSIPjaAnzeige der Kontakte über LDAP
9.3 Globales Telefonbuch aus TeamsipjaAnzeige der Kontakte über LDAP
9.4 Callcenter Anmeldung mit Status Anzeigeja

9.5 Neustart über SIP Notifyja

sip notify yealink-reboot-cfg  10001909a

[yealink-reboot-cfg]
Event=>check-sync
reboot=>false

9.6 Reload über SIP Notifyja

9.7 Klingelton Unterscheidung intern/externja

distinctive_ring_tones.alert_info.1.text = Intern
distinctive_ring_tones.alert_info.1.ringer = 6

TeamSIP Provisionierungs Template

Nutzbare Tasten

Unten aufgeführtes Beispiel nutzt 28 belegbare Tasten in der TeamSIP Weboberfläche, hier mit Unterstützung Erweiterungsmodul.

Am Telefon nutzbar sind die Tasten neben dem Display und mit Ebenen Umschalt-Taste.

Konfigurationsbeispiel

Parameter für dieses Template:

NameVorgabe
TF_FIRMWARET5x-58.80.0.10.rom
TF_TRANSPORT0
TF_SERVERPORT5060
TF_INTERN_LAENGExx
TF_ALERT_INTERN6
TF_VORWAHL089
TF_LOGO_PATHhttp://berlix2-lb1.teamfon.com/images/
TF_LOGO_FILEteamfon_ybg_black.jpg
TF_KEYLENGTH0

Das geteste Telefon wurde mit dieser Provisionierungsvorlage als Telefon in TeamSIP konfiguriert:

TeamSIP Telefon Template

#!version:1.0.0.1
 
##File header "#!version:1.0.0.1" can not be edited or deleted, and must be placed in the first line.##
##This template file is applicable to SIP-T28P/T26P/T22P/T20P/T21P/T19P/T46G/T42G/T41P IP phones running firmware version 72 or later.##
##For more information on configuration parameters, refer to Yealink_SIP-T2_Series_T19P_T4_Series_IP_Phones_Auto_Provisioning_Guide.##
 
 
##manuell
phone_setting.talk_and_dial_power_led_enable = 1
 
 
##Lautstärke Hörer
voice.handset.spk_vol = 15
 
 
### Textlänge 0=Standard 1=erweitert
features.config_dsskey_length = %TF_KEYLENGTH%
 
 
### Datumsformat
local_time.date_format = 5
 
 
### interner Klingelton aktivieren
account.1.alert_info_url_enable = 1
distinctive_ring_tones.alert_info.1.text = Intern
distinctive_ring_tones.alert_info.1.ringer = %TF_ALERT_INTERN%
 
### TFCUST-110962
features.direct_ip_call_enable = 0
account.1.sip_trust_ctrl = 1 
 
 
#######################################################################################
## Account1 Basic Settings ##
#######################################################################################
account.1.enable = 1
account.1.label = %TF_NUMMER%
account.1.display_name = %TF_NUMMER%
account.1.auth_name = %TF_ACCOUNT%
account.1.user_name = %TF_ACCOUNT%
account.1.password = %TF_PASSWORD%
account.1.sip_server_host = %TF_SIPSERVER%
account.1.sip_server_port = %TF_SERVERPORT%
account.1.sip_server_type = 0
account.1.outbound_proxy_enable = 0
account.1.outbound_host =
account.1.outbound_port = %TF_SERVERPORT%
account.1.transport = %TF_TRANSPORT%
account.1.backup_outbound_host =
account.1.backup_outbound_port = %TF_SERVERPORT%
account.1.proxy_require =
account.1.anonymous_call = 0
account.1.reject_anonymous_call = 0
account.1.expires = 900
account.1.sip_listen_port = %TF_SERVERPORT%
account.1.100rel_enable = 0
account.1.precondition = 0
#
account.1.cid_source = 2
account.1.session_timer.enable = 0
account.1.session_timer.expires =
account.1.session_timer.refresher = 0
account.1.enable_user_equal_phone = 0
account.1.srtp_encryption = 0
account.1.ptime = 0
account.1.shared_line =
account.1.dialoginfo_callpickup =
account.1.dtmf.type = 1
account.1.dtmf.info_type = 0
account.1.dtmf.dtmf_payload = 101
account.1.nat.nat_traversal = 0
account.1.nat.stun_server = stun.teamfon.com
account.1.nat.stun_port = 10000
account.1.nat.udp_update_enable = 1
account.1.nat.udp_update_time = 30
account.1.nat.rport = 0
account.1.advanced.timer_t1 = 2
account.1.advanced.timer_t2 = 4
account.1.advanced.timer_t4 = 5
account.1.blf.subscribe_period = 3600
account.1.blf.blf_list_uri =
account.1.codec.1.enable = 1
account.1.codec.1.payload_type = PCMU
account.1.codec.1.priority = 3
account.1.codec.1.rtpmap = 0
account.1.codec.2.enable = 1
account.1.codec.2.payload_type = PCMA
account.1.codec.2.priority = 2
account.1.codec.2.rtpmap = 8
account.1.codec.3.enable = 0
account.1.codec.3.payload_type = G723_53
account.1.codec.3.priority = 0
account.1.codec.3.rtpmap = 4
account.1.codec.4.enable = 0
account.1.codec.4.payload_type = G723_63
account.1.codec.4.priority = 0
account.1.codec.4.rtpmap = 4
account.1.codec.5.enable = 0
account.1.codec.5.payload_type = G729
account.1.codec.5.priority = 3
account.1.codec.5.rtpmap = 18
account.1.codec.6.enable = 1
account.1.codec.6.payload_type = G722
account.1.codec.6.priority = 1
account.1.codec.6.rtpmap = 9
account.1.codec.7.enable = 0
account.1.codec.7.payload_type = iLBC
account.1.codec.7.priority = 0
account.1.codec.7.rtpmap = 102
account.1.codec.8.enable = 0
account.1.codec.8.payload_type = G726-16
account.1.codec.8.priority = 0
account.1.codec.8.rtpmap = 112
account.1.codec.9.enable = 0
account.1.codec.9.payload_type = G726-24
account.1.codec.9.priority = 0
account.1.codec.9.rtpmap = 102
account.1.codec.10.enable = 0
account.1.codec.10.payload_type = G726-32
account.1.codec.10.priority = 0
account.1.codec.10.rtpmap = 2
account.1.codec.11.enable = 0
account.1.codec.11.payload_type = G726-40
account.1.codec.11.priority = 0
account.1.codec.11.rtpmap = 104
#
network.internet_port.type = 0
network.internet_port.ip =
network.internet_port.mask =
network.internet_port.gateway =
network.primary_dns =
network.secondary_dns =
network.pppoe.user =
network.pppoe.password =
network.bridge_mode = 1
network.pc_port.ip = 10.0.0.1
network.pc_port.mask = 255.255.255.0
network.pc_port.dhcp_server = 1
network.dhcp.start_ip = 10.0.0.10
network.dhcp.end_ip = 10.0.0.100
network.vlan.internet_port_enable = 0
network.vlan.internet_port_vid = 0
network.vlan.internet_port_priority = 0
network.vlan.pc_port_enable = 0
network.vlan.pc_port_vid = 0
network.vlan.pc_port_priority = 0
network.qos.signaltos = 40
network.qos.rtptos = 40
network.port.max_rtpport = 11800
network.port.min_rtpport = 11780
 
# syslog note
#syslog.server =
 
#
lang.gui = German
lang.wui = German
 
#
local_time.time_zone = +1
local_time.time_zone_name = Germany(Berlin)
local_time.ntp_server1 = %TF_SIPSERVER%
local_time.ntp_server2 = ntp.tmwr.de
 
#
phone_setting.inter_digit_time = 4
phone_setting.flash_hook_timer = 1
phone_setting.lock = 0
phone_setting.ring_type =
phone_setting.contrast = 2
phone_setting.active_backlight_level = 10
phone_setting.backlight_time = 1800
phone_setting.product_name =
sip.call_fail_use_reason.enable = 0

#
call_waiting.enable = 1
 
#
features.hotline_number =
features.busy_tone_delay =
features.key_tone = 0
features.pound_key.mode = 1
features.dnd.large_icon.enable = 1
 
#
phone_setting.emergency.number = 110,112
 
 
 
 
#######################################################################################
## Transfer ##
#######################################################################################
 
transfer.semi_attend_tran_enable = 1
transfer.blind_tran_on_hook_enable = 0
transfer.tran_others_after_conf_enable = 0
transfer.on_hook_trans_enable =
transfer.dsskey_deal_type = 1
transfer.multi_call_trans_enable =
 
 
 
 
#
#######################################################################################
## Line Key ##
#######################################################################################
###Except T19D Model
###T21D/T20P X ranges from 1 to 2
###T22P/T26P X ranges from 1 to 3
###T28P X ranges from 1 to 6
###T41P/T42G X ranges from 1 to 15
###T46G X ranges from 1 to 27
linekey.1.line = 1
linekey.1.value = %TF_NTNUMMER_1%
linekey.1.pickup_value = **
linekey.1.type = 16
linekey.1.label = %TF_NTNAME_1%

linekey.2.line = 1
linekey.2.value = %TF_NTNUMMER_2%
linekey.2.pickup_value = **
linekey.2.type = 16
linekey.2.label = %TF_NTNAME_2%
 
linekey.3.line = 1
linekey.3.value = %TF_NTNUMMER_3%
linekey.3.pickup_value = **
linekey.3.type = 16
linekey.3.label = %TF_NTNAME_3%
 
linekey.4.sub_type = BLF
linekey.4.line = 1
linekey.4.value = %TF_NTNUMMER_4%
linekey.4.pickup_value = **
linekey.4.type = 16
linekey.4.label = %TF_NTNAME_4%
 
linekey.5.sub_type = BLF
linekey.5.line = 1
linekey.5.value = %TF_NTNUMMER_5%
linekey.5.pickup_value = **
linekey.5.type = 16
linekey.5.label = %TF_NTNAME_5%
 
linekey.6.sub_type = BLF
linekey.6.line = 1
linekey.6.value = %TF_NTNUMMER_6%
linekey.6.pickup_value = **
linekey.6.type = 16
linekey.6.label = %TF_NTNAME_6%
 
linekey.7.sub_type = BLF
linekey.7.line = 1
linekey.7.value = %TF_NTNUMMER_7%
linekey.7.pickup_value = **
linekey.7.type = 16
linekey.7.label = %TF_NTNAME_7%
 
linekey.8.sub_type = BLF
linekey.8.line = 1
linekey.8.value = %TF_NTNUMMER_8%
linekey.8.pickup_value = **
linekey.8.type = 16
linekey.8.label = %TF_NTNAME_8%

linekey.9.sub_type = BLF
linekey.9.line = 1
linekey.9.value = %TF_NTNUMMER_9%
linekey.9.pickup_value = **
linekey.9.type = 16
linekey.9.label = %TF_NTNAME_9%
 
linekey.10.sub_type = BLF
linekey.10.line = 1
linekey.10.value = %TF_NTNUMMER_10%
linekey.10.pickup_value = **
linekey.10.type = 16
linekey.10.label = %TF_NTNAME_10%
 
 
linekey.11.sub_type = BLF
linekey.11.line = 1
linekey.11.value = %TF_NTNUMMER_11%
linekey.11.pickup_value = **
linekey.11.type = 16
linekey.11.label = %TF_NTNAME_11%
 
linekey.12.sub_type = BLF
linekey.12.line = 1
linekey.12.value = %TF_NTNUMMER_12%
linekey.12.pickup_value = **
linekey.12.type = 16
linekey.12.label = %TF_NTNAME_12%
 
linekey.13.sub_type = BLF
linekey.13.line = 1
linekey.13.value = %TF_NTNUMMER_13%
linekey.13.pickup_value = **
linekey.13.type = 16
linekey.13.label = %TF_NTNAME_13%
 
linekey.14.sub_type = BLF
linekey.14.line = 1
linekey.14.value = %TF_NTNUMMER_14%
linekey.14.pickup_value = **
linekey.14.type = 16
linekey.14.label = %TF_NTNAME_14%
 
linekey.15.sub_type = BLF
linekey.15.line = 1
linekey.15.value = %TF_NTNUMMER_15%
linekey.15.pickup_value = **
linekey.15.type = 16
linekey.15.label = %TF_NTNAME_15%
 
linekey.16.sub_type = BLF
linekey.16.line = 1
linekey.16.value = %TF_NTNUMMER_16%
linekey.16.pickup_value = **
linekey.16.type = 16
linekey.16.label = %TF_NTNAME_16%

linekey.17.sub_type = BLF
linekey.17.line = 1
linekey.17.value = %TF_NTNUMMER_17%
linekey.17.pickup_value = **
linekey.17.type = 16
linekey.17.label = %TF_NTNAME_17%

linekey.18.sub_type = BLF
linekey.18.line = 1
linekey.18.value = %TF_NTNUMMER_18%
linekey.18.pickup_value = **
linekey.18.type = 16
linekey.18.label = %TF_NTNAME_18%

linekey.19.sub_type = BLF
linekey.19.line = 1
linekey.19.value = %TF_NTNUMMER_19%
linekey.19.pickup_value = **
linekey.19.type = 16
linekey.19.label = %TF_NTNAME_19%
 
linekey.20.sub_type = BLF
linekey.20.line = 1
linekey.20.value = %TF_NTNUMMER_20%
linekey.20.pickup_value = **
linekey.20.type = 16
linekey.20.label = %TF_NTNAME_20%
 
linekey.21.sub_type = BLF
linekey.21.line = 1
linekey.21.value = %TF_NTNUMMER_21%
linekey.21.pickup_value = **
linekey.21.type = 16
linekey.21.label = %TF_NTNAME_21%

linekey.22.sub_type = BLF
linekey.22.line = 1
linekey.22.value = %TF_NTNUMMER_22%
linekey.22.pickup_value = **
linekey.22.type = 16
linekey.22.label = %TF_NTNAME_22%

linekey.23.sub_type = BLF
linekey.23.line = 1
linekey.23.value = %TF_NTNUMMER_23%
linekey.23.pickup_value = **
linekey.23.type = 16
linekey.23.label = %TF_NTNAME_23%
 
linekey.24.sub_type = BLF
linekey.24.line = 1
linekey.24.value = %TF_NTNUMMER_24%
linekey.24.pickup_value = **
linekey.24.type = 16
linekey.24.label = %TF_NTNAME_24%
 
linekey.25.sub_type = BLF
linekey.25.line = 1
linekey.25.value = %TF_NTNUMMER_25%
linekey.25.pickup_value = **
linekey.25.type = 16
linekey.25.label = %TF_NTNAME_25%
 
linekey.26.sub_type = BLF
linekey.26.line = 1
linekey.26.value = %TF_NTNUMMER_26%
linekey.26.pickup_value = **
linekey.26.type = 16
linekey.26.label = %TF_NTNAME_26%
 
linekey.27.sub_type = BLF
linekey.27.line = 1
linekey.27.value = %TF_NTNUMMER_27%
linekey.27.pickup_value = **
linekey.27.type = 16
linekey.27.label = %TF_NTNAME_27%
 
linekey.28.sub_type = BLF
linekey.28.line = 1
linekey.28.value = %TF_NTNUMMER_28%
linekey.28.pickup_value = **
linekey.28.type = 16
linekey.28.label = %TF_NTNAME_28%
 
#######################################################################################
## Programable Key ##
#######################################################################################
###T20P X ranges from 1 to 9
###T28P/T26P X ranges from 1 to 14
###T41P/T42G/T19P/T21P X ranges from 1 to 11
###T46G/T22P X ranges from 1 to 13
programablekey.2.type = 38
programablekey.2.label = Kontakte
 
# voice note
voice.vad = 0
voice.cng = 1
voice.echo_cancellation = 1
# voice.side_tone = -3
voice.jib.adaptive = 1
voice.jib.min = 0
voice.jib.max = 300
voice.jib.normal = 120
 
#
voice_mail.number.1 = *99
voice_mail.number.2 = *99
voice_mail.number.3 = *99
voice_mail.number.4 = *99
voice_mail.number.5 = *99
voice_mail.number.6 = *99
 
# voice note
voice.tone.country = Germany
voice.tone.dial =
voice.tone.ring =
voice.tone.busy =
voice.tone.congestion =
voice.tone.callwaiting =
voice.tone.dialrecall =
voice.tone.record =
voice.tone.info =
voice.tone.stutter =
voice.tone.message =
voice.tone.autoanswer =
 
# ldap note
ldap.enable = 1
ldap.name_filter = (&(telNrBusiness1=*)(sn=%))
ldap.number_filter =
ldap.host = %TF_SIPSERVER%
ldap.port = 389
ldap.base =
ldap.user = uid=%TF_ACCOUNT%,ou=authentication,dc=teamfom,dc=de
ldap.password = %TF_PASSWORD%
ldap.max_hits = 100
ldap.name_attr = sn cn
ldap.numb_attr = telNrBusiness1 telNrBusiness2 telNrMobile telNrPrivate
ldap.display_name = %cn
ldap.version = 3
ldap.base = ou=Teamfon,ou=userdata,ou=appls,dc=teamware,dc=de
ldap.ldap_sort = 0
ldap.call_in_lookup = 0
 
#
auto_provision.mode = 7
#
auto_provision.schedule.periodic_minute =
auto_provision.schedule.time_from = 02:00
auto_provision.schedule.time_to = 03:00
auto_provision.schedule.dayofweek = 0123456
#
auto_provision.pnp_enable = 0
auto_provision.dhcp_option.list_user_options =
#
auto_provision.server.url = http://%TF_SIPSERVER%/yealink
# security note
security.user_password = admin:team%TF_CONTEXT%
security.user_password = user:
#
 
 
#######################################################################################
## Dial Plan ##
#######################################################################################
 
 
 
dialplan.area_code.code =
dialplan.area_code.min_len = 1
dialplan.area_code.max_len = 15
 
dialplan.area_code.line_id =
 
dialplan.block_out.number.1 =
 
dialplan.block_out.line_id.1 =

dialplan.item.1 = 1,([1-9]%TF_INTERN_LAENGE%.),%TF_VORWAHL%$1
 
#######################################################################################
## Firmware ##
#######################################################################################
 
 
 
firmware.url = http://%TF_SIPSERVER%/yealink/firmware/%TF_FIRMWARE%
wallpaper_upload.url = %TF_LOGO_PATH%%TF_LOGO_FILE%
phone_setting.backgrounds = Config:%TF_LOGO_FILE%
HTML/XML